Tekin RS ESC sensored
Tech Adept
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Sensored-mode with Turbo w/ 11.5R (boost:50, turbo:5, delay:0.4s, S:3000ish, E:14000ish)
Dual mode with 7.5R (timing advance:80)
Both motors do not have adjustable timing.
They are about equal in speed. 11.5R was a little easier to drive because it was not as punchy as the 7.5R. However, the temp for 11.5R was about 65C while the 7.5R was about 40C. Outside temp was about 14C.
This was on a medium sized track, touring. Both FDR were about the same, around 7.8ish.
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Hello I will be running v203 for the first time tomorrow at the roar regional championship and was wondering what a good set up would be for this track layout. what would be a good round about roll out to start with also.track size is 90x40 feet
thanks very much in advance
duo 2---17.5
1s 12 scale
tq booster
thanks very much in advance
duo 2---17.5
1s 12 scale
tq booster
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
The Cyclone TC has a 39 tooth diff pulley and a 18 tooth layshaft pulley, so this might account for your difference in speed if you have a 17 tooth layshaft pulley. With 39T diff pulley, 17T layshaft pulley, 96T spur and 40T pinion, your FDR is 5.506 while the TC with the same except for 18T layshaft pulley has a 5.2 FDR.
my laysaft pullies on my cyclone are the 3racing pullies where i can change from 16t-17t-18t. im putting the 18 tooth on since i just got the tc belts so i am going to be the same fdr i hope. i know my car weighs alittle more since its the cyclone s. im just starting to think that my motor might be getting tiered or i need to give it a good cleaning
Tech Adept
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
New shell I just painted up for the Xray, all the Tekin logos are hand painted
![](http://img28.imageshack.us/img28/3535/picture132.jpg)
![](http://img62.imageshack.us/img62/3852/picture142b.jpg)
![](http://img28.imageshack.us/img28/3535/picture132.jpg)
![](http://img62.imageshack.us/img62/3852/picture142b.jpg)
![](http://img28.imageshack.us/img28/6149/picture141i.jpg)
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
you might need to a new blue body when the sxx ss start popping up around soon
![Smilie](https://www.rctech.net/forum/classic_images/smilies/smile.gif)
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
you are right on one thing, that being a new body everytime the LRP goes up in smoke and melts the shell ![Laughing](https://www.rctech.net/forum/classic_images/smilies/laugh2.gif)
![Laughing](https://www.rctech.net/forum/classic_images/smilies/laugh2.gif)
![Laughing](https://www.rctech.net/forum/classic_images/smilies/laugh2.gif)
![Laughing](https://www.rctech.net/forum/classic_images/smilies/laugh2.gif)
![Laughing](https://www.rctech.net/forum/classic_images/smilies/laugh2.gif)
![Laughing](https://www.rctech.net/forum/classic_images/smilies/laugh2.gif)
![Laughing](https://www.rctech.net/forum/classic_images/smilies/laugh2.gif)
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
NICE LID JAMES,that should be shelved ts to nice to run
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Thanks Jamie, yeah sometimes it gets like that and you cry the first scrape it gets lol
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Medium sized carpet track with decent grip and a fairly fast layout.
Duo 1 10.5 in the first hole (least timing)
Boost 45
Turbo 9
Delay .6
ramp 1 (runs cooler and no slower vs. 2 and 3)
Start rpm 2xxx
End rpm 10000
rollout 67mm. Anything under about 64 results in slow straight speeds no matter how much timing I put in it.
I should also point out that the only guy with a faster laptime than me is running even less timing. More timing does not always equal more speed.
Tech Master
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Very nice body James.
![Nodding](https://www.rctech.net/forum/classic_images/smilies/nod.gif)
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
2 units of Rs pro with the hotwire will be arriving for me n my friend in 2 days. I read alot about it and decide to go for it instead of the LRP Sxx and black diamond. I have the software ready in my pc and am just waiting for it to arrive. Is anyone kind enough to share previous settings on the rs pro hotwire (203) in previous races or setup? I love the function but ofcourse would not like to blow it just incase i did the worng setting to make it fast. Our track here are Asphlat with 50meters straight with lots of technical sharp curves. Motor class race here are Mod, Stock 11.5t and sometimes novice stock 9T. I have succesfully won the novice class using 107 SP firmware with ease and ofcourse i would like to have another victory but using only 11.5t setting on the tekin. So is anyone kind enough to share lots of setting which could help me out please?