GM Brushless
#1231
genius 120 gen 2 if totally new, not only a new software
that software won't work for gen1 speedos.
there won't be anything newer than 7.x for the gen1 speedo.
that software won't work for gen1 speedos.
there won't be anything newer than 7.x for the gen1 speedo.
#1232
gm 120
Hi Martyn,
Thanks for your reply.
Do you have a speedo setting for 10.5 with 7.x firmware
regards
Thanks for your reply.
Do you have a speedo setting for 10.5 with 7.x firmware
regards
#1233
Tech Adept
GM genius 120 version 7.0
just managed to get one on ebay ver 7.0?
does anyone know if I will be able to download the newer ver 7.2 software into the speedo?
does anyone know if I will be able to download the newer ver 7.2 software into the speedo?
#1235
Tech Adept
sorry about that, but this thread has 83 pages? I had a quick flip through the more recent pages and must have missed it.
i am sure you do not expect people coming in here to trawl through all the pages just to find out the above fact.
#1236
Tech Fanatic
iTrader: (1)
cheers for the update and for bringing the fact up to date.
sorry about that, but this thread has 83 pages? I had a quick flip through the more recent pages and must have missed it.
i am sure you do not expect people coming in here to trawl through all the pages just to find out the above fact.
sorry about that, but this thread has 83 pages? I had a quick flip through the more recent pages and must have missed it.
i am sure you do not expect people coming in here to trawl through all the pages just to find out the above fact.
search button a little over then post ;P
don't worry, GM are good but older version can be upgrade to new software
only at GM.
Martin wrote something about new GM's but they are still unavailable at
stores maybe they will be updatable by owner or maybe not...
m.
#1237
Tech Adept
After going through 83 pages and 1230+ posts,
for 10.5T
Cheers Martin for the above.
My question and before M Abrams decide to 'shell' me again, I do not think I have read this anywhere.
Can the above be used with firmware 7.0?
If I have a second hand Genius 120 FW7.0, is there anyway that I can find out if any of the modes have already been copied over? Or is it better if I just do a reset and start from factory setings?
... Speed Setup for 13,5 / 17,5T with Lipo and FIRMWARE 7.2!!
please only use this setting for FW72
before putting that program on,
read out your speedo,
then save the transmitterdata to your pc,
load that setting,
load your just saved transmitter data,
send to the speedo
...
please only use this setting for FW72
before putting that program on,
read out your speedo,
then save the transmitterdata to your pc,
load that setting,
load your just saved transmitter data,
send to the speedo
...
My question and before M Abrams decide to 'shell' me again, I do not think I have read this anywhere.
Can the above be used with firmware 7.0?
If I have a second hand Genius 120 FW7.0, is there anyway that I can find out if any of the modes have already been copied over? Or is it better if I just do a reset and start from factory setings?
#1238
#1239
Chinaman,
That pic is of the Gen2 version, as the capacitor is in stick for, version one had them built onto the board of the speed controller
That pic is of the Gen2 version, as the capacitor is in stick for, version one had them built onto the board of the speed controller
#1240
Tech Master
This way is the speedo a bit shorter.
#1241
Tech Addict
After going through 83 pages and 1230+ posts,
for 10.5T
Cheers Martin for the above.
My question and before M Abrams decide to 'shell' me again, I do not think I have read this anywhere.
Can the above be used with firmware 7.0?
If I have a second hand Genius 120 FW7.0, is there anyway that I can find out if any of the modes have already been copied over? Or is it better if I just do a reset and start from factory setings?
for 10.5T
Cheers Martin for the above.
My question and before M Abrams decide to 'shell' me again, I do not think I have read this anywhere.
Can the above be used with firmware 7.0?
If I have a second hand Genius 120 FW7.0, is there anyway that I can find out if any of the modes have already been copied over? Or is it better if I just do a reset and start from factory setings?
See text:
"please only use this setting for FW72"
#1242
Tech Fanatic
iTrader: (1)
did you mean this ...
Attachment 551038
obtained from GM website but could not post the URL ... i am too fresh out of the factory
or is this version 2?
Attachment 551038
obtained from GM website but could not post the URL ... i am too fresh out of the factory
or is this version 2?
again by GM. Martin wrote some, and main eng. Ralf wrote some
Who know who has right
This is old one:
About your 7.0 ver, just do reset and try mode 6 or mode 8 (more rpms but
will be hot!). I know that settings from 7.2 maybe will work or maybe not.
GM made some updates and sometimes everything change
Btw, if you have USB interface, can you post downloaded data from mode 6 and mode 8?
Regards!
m.
ps: will not "shell" you
#1243
Tech Adept
will download some data from mode 6 and 8 and let you guys decipher ...
#1245
Tech Rookie
hi just got a gm 120 with 7.2 software
can anybody tell me what the settings timing 1 and 2 do on the genius tool 1.3.6 software
sorry if this has been covered earlier but could not find the info in all the pages.
can anybody tell me what the settings timing 1 and 2 do on the genius tool 1.3.6 software
sorry if this has been covered earlier but could not find the info in all the pages.