Team Losi JRXS Type-R
#8417
Tech Adept
iTrader: (8)
Man I love this car! Just had to throw that out there...
Last Friday was my first club race with the car. Tight indoor carpet track with foams. There were 7 sedans and for my first race I couldn't believe how hooked up I was. People were coming up to me and raving about the car... I owe a lot to this thread I guess, but the car is just dialed. Competition consisted of another Type R, a TC4, 2 XXXS's and an old saddle pack XRay. My results were 3rd, 1st, 2nd, 3rd in the main. Poor results were totally my fault as an amateur on-roader, but I'll get em this week.
As a side note, does anyone make alloy castor blocks out there? I saw some earlier posts on using Tamalie TC5 blocks, but that's it. I've snapped a couple now and it seems to be the weak spot on the car. I'd pay for a set of 4 degree blocks!
Sorry for the late response... My local shop had the tray on back order for a couple months now and finally got it in!
Last Friday was my first club race with the car. Tight indoor carpet track with foams. There were 7 sedans and for my first race I couldn't believe how hooked up I was. People were coming up to me and raving about the car... I owe a lot to this thread I guess, but the car is just dialed. Competition consisted of another Type R, a TC4, 2 XXXS's and an old saddle pack XRay. My results were 3rd, 1st, 2nd, 3rd in the main. Poor results were totally my fault as an amateur on-roader, but I'll get em this week.
As a side note, does anyone make alloy castor blocks out there? I saw some earlier posts on using Tamalie TC5 blocks, but that's it. I've snapped a couple now and it seems to be the weak spot on the car. I'd pay for a set of 4 degree blocks!
Sorry for the late response... My local shop had the tray on back order for a couple months now and finally got it in!
#8418
No alloy ones I am aware of, but if you have axle protruding out past the nut I suggest you cut it down flush with the nut so it is not catching the boards. That can be an issue causing you to break hubs. Well not causing, but helping out when you are hitting boards.
#8423
Alright, so building my second jrxs-r. First one I bought used.
Building the diffs, it seems the diff spring is too long. I noticed that it didn't seem right for the thrust bearing to be exposed, tightening one for a while figuring it would collapse the spring, but eventually I heard a loud crack and it didn't compress the spring at all.
Finally took apart a diff from the first car. Comparing the diff springs, the correct one is silver in color, 3 turns in the spring and .267in. The ones I got in this kit are black in color, 4 turns in the spring and .429 in.
Suggestions?
Building the diffs, it seems the diff spring is too long. I noticed that it didn't seem right for the thrust bearing to be exposed, tightening one for a while figuring it would collapse the spring, but eventually I heard a loud crack and it didn't compress the spring at all.
Finally took apart a diff from the first car. Comparing the diff springs, the correct one is silver in color, 3 turns in the spring and .267in. The ones I got in this kit are black in color, 4 turns in the spring and .429 in.
Suggestions?
#8424
Tech Adept
iTrader: (8)
I have a pair of ti ball studs from Losi to set up a front camber link on my car in case I wanted to ditch the JR link. (Part #LOSA9949)
I would like to set up a long rear camber link set-up on my car... I know I need a 1 inch Lunsford turnbuckle, but does anyone know the correct ball stud to get for the outer hub carrier position? Will the one I have work or is there too much thread? I see "long ball stud" a lot in set ups, but which one?
I would like to set up a long rear camber link set-up on my car... I know I need a 1 inch Lunsford turnbuckle, but does anyone know the correct ball stud to get for the outer hub carrier position? Will the one I have work or is there too much thread? I see "long ball stud" a lot in set ups, but which one?
#8425
Tech Champion
iTrader: (73)
Alright, so building my second jrxs-r. First one I bought used.
Building the diffs, it seems the diff spring is too long. I noticed that it didn't seem right for the thrust bearing to be exposed, tightening one for a while figuring it would collapse the spring, but eventually I heard a loud crack and it didn't compress the spring at all.
Finally took apart a diff from the first car. Comparing the diff springs, the correct one is silver in color, 3 turns in the spring and .267in. The ones I got in this kit are black in color, 4 turns in the spring and .429 in.
Suggestions?
Building the diffs, it seems the diff spring is too long. I noticed that it didn't seem right for the thrust bearing to be exposed, tightening one for a while figuring it would collapse the spring, but eventually I heard a loud crack and it didn't compress the spring at all.
Finally took apart a diff from the first car. Comparing the diff springs, the correct one is silver in color, 3 turns in the spring and .267in. The ones I got in this kit are black in color, 4 turns in the spring and .429 in.
Suggestions?
#8426
Alright, so building my second jrxs-r. First one I bought used.
Building the diffs, it seems the diff spring is too long. I noticed that it didn't seem right for the thrust bearing to be exposed, tightening one for a while figuring it would collapse the spring, but eventually I heard a loud crack and it didn't compress the spring at all.
Finally took apart a diff from the first car. Comparing the diff springs, the correct one is silver in color, 3 turns in the spring and .267in. The ones I got in this kit are black in color, 4 turns in the spring and .429 in.
Suggestions?
Building the diffs, it seems the diff spring is too long. I noticed that it didn't seem right for the thrust bearing to be exposed, tightening one for a while figuring it would collapse the spring, but eventually I heard a loud crack and it didn't compress the spring at all.
Finally took apart a diff from the first car. Comparing the diff springs, the correct one is silver in color, 3 turns in the spring and .267in. The ones I got in this kit are black in color, 4 turns in the spring and .429 in.
Suggestions?
#8428
I have a pair of ti ball studs from Losi to set up a front camber link on my car in case I wanted to ditch the JR link. (Part #LOSA9949)
I would like to set up a long rear camber link set-up on my car... I know I need a 1 inch Lunsford turnbuckle, but does anyone know the correct ball stud to get for the outer hub carrier position? Will the one I have work or is there too much thread? I see "long ball stud" a lot in set ups, but which one?
I would like to set up a long rear camber link set-up on my car... I know I need a 1 inch Lunsford turnbuckle, but does anyone know the correct ball stud to get for the outer hub carrier position? Will the one I have work or is there too much thread? I see "long ball stud" a lot in set ups, but which one?
#8429
Tech Adept
iTrader: (8)
You don't have to get the Lunsford turnbuckle if you don't want to. I use offroad ball cups on the tower side of the link to give me the length I need to run the long camber link. You have to cut a little off to get it to work right but cheaper then buying turn buckles. The long ball stud has nothing to do with the thread, but how high the head of the ball stud sticks up from the base.
On the ball stud question; I thought it wasn't the thread length... What ball stud should I get though?
#8430
Tech Addict
iTrader: (16)
I got my Type R all put together. Tomorrow will be the first race. I am a rookie to electric onroad, but am very experienced in 1/8th buggy. I have a question. I am using a novak gtb with 10.5 motor and foam tires. What throttle profile on the speed control should I use? The track is a tight small course with lots of low speed turns.