2LikesGo-Tech Engines Thread
11-02-2007 | 12:21 AM
#361
Tech Rookie
Joined: Jun 2007
Posts: 8
Kdrrt you cannot use nova plugs in the go engine as well as mccoy plugs, they will work but they will protrude too far into the combustion chamber causing decreased efficency. It must be a o.s style short shank plug to work, If you resort to mail order, amain sells the 6 pack of go plugs. A o.s. a3 will work as well.
Vigilante sounds like the perfect combo for that track. The x-ray clutch is also very good, I reccomend the 1.71 shoes with 1.0 springs, and if the bottom is too strong try the .9 springs.
Nitrojunkie, the 5port piston and sleeve will work fine in the 7port crankcase.
Vigilante sounds like the perfect combo for that track. The x-ray clutch is also very good, I reccomend the 1.71 shoes with 1.0 springs, and if the bottom is too strong try the .9 springs.
Nitrojunkie, the 5port piston and sleeve will work fine in the 7port crankcase.
11-03-2007 | 04:04 PM
#363
od97t plug.. tried it today no good imo put the P3 plug in and it was great and easier to tune with and better run time so i seen. i got 7.5 mins with p3 plug and a jp3 pipe i think if i get a better pipe i might get more run time.. plus this is all with just .5 gallon on the motor...
11-03-2007 | 04:28 PM
#365
i may be wrong but what i would do is lean bottom 1 hr and richin top maybe .5 to 1h more then u did.. that should do good for you.. if u go out and the motor still runs good and u temp it at 180 to 200 id lean .5 to 1hr more then it should be set... might get someone else to chim in to on it...
11-03-2007 | 04:56 PM
#366
If you guys have access to LRP plugs, i would be using them IMO. I have tried most other plugs and find myself back on the LRP plugs every time! I have three Go 5P one with a Massive Mods Stage 5, one stock and one with a Turbo head, I run #6 plugs in the non turbo and 6T and 7T LRP plugs in the turbos.
I also am just about to run in a GO 28 6+2 pro motor and 28 pullstart motor for my savage. If they go anything like the the 21 5P they should be a very powerful mill!!!
I also am just about to run in a GO 28 6+2 pro motor and 28 pullstart motor for my savage. If they go anything like the the 21 5P they should be a very powerful mill!!!
11-03-2007 | 06:27 PM
#369
Tech Regular
iTrader: (14)
Joined: Jul 2007
Posts: 298
I finally got my RC8 and Go Tech 3 port up and running. I have to tell you that for $100, the 3 port rips
! I'm thoroughly impressed by the motor and feel it's money well spent!
Question... the throttle ball cup that comes with the rc8 slides right over the ball on the carb. I had to put a little rubber band to hold it on
. What ball cup should I get that will be the right fit? Thanks!
! I'm thoroughly impressed by the motor and feel it's money well spent!Question... the throttle ball cup that comes with the rc8 slides right over the ball on the carb. I had to put a little rubber band to hold it on
. What ball cup should I get that will be the right fit? Thanks!
11-03-2007 | 08:54 PM
#371
ran the RC8 today, and yes... the stock ball cup is to large for the GO carb.
A xray one works great.
Took the win today as well thanks to my STUPID fast GO 7 Port. Very consistant power throughout the day and the motor felt exactly the same for the whole main.
I tried the 053 pipe and it seemed to tame the motor down just a little over the 086 i usually run. I really liked it so i plan to run it for a while to get a better feel of which i truely like better.
YGM Russell.
A xray one works great.
Took the win today as well thanks to my STUPID fast GO 7 Port. Very consistant power throughout the day and the motor felt exactly the same for the whole main.
I tried the 053 pipe and it seemed to tame the motor down just a little over the 086 i usually run. I really liked it so i plan to run it for a while to get a better feel of which i truely like better.
YGM Russell.
11-03-2007 | 09:06 PM
#372
ran the RC8 today, and yes... the stock ball cup is to large for the GO carb.
A xray one works great.
Took the win today as well thanks to my STUPID fast GO 7 Port. Very consistant power throughout the day and the motor felt exactly the same for the whole main.
I tried the 053 pipe and it seemed to tame the motor down just a little over the 086 i usually run. I really liked it so i plan to run it for a while to get a better feel of which i truely like better.
YGM Russell.
A xray one works great.
Took the win today as well thanks to my STUPID fast GO 7 Port. Very consistant power throughout the day and the motor felt exactly the same for the whole main.
I tried the 053 pipe and it seemed to tame the motor down just a little over the 086 i usually run. I really liked it so i plan to run it for a while to get a better feel of which i truely like better.
YGM Russell.
11-03-2007 | 10:45 PM
#374
Tech Regular
Joined: Sep 2007
Posts: 387
From: Australia,Wollongong
yea the GO techs are going very well in terms of selling and i couldnt believe how well they go for only 230AUD, yea so as soon as one of the 2 online shops have them back in ill be sure to pick one up no doubt.
all the best and will let you know how things go when and if i get a GO tech.
all the best and will let you know how things go when and if i get a GO tech.
11-04-2007 | 01:38 AM
#375
yea the GO techs are going very well in terms of selling and i couldnt believe how well they go for only 230AUD, yea so as soon as one of the 2 online shops have them back in ill be sure to pick one up no doubt.
all the best and will let you know how things go when and if i get a GO tech.
all the best and will let you know how things go when and if i get a GO tech.