NEW HOBBYWING STOCK SUPERCHARGED SOFTWARE
Tech Elite
iTrader: (14)
edit
Tech Addict
iTrader: (14)
I've run it in stock TC, FDR at 3.92-4.0, approx. 45* timing on the end bell. It's plenty fast on a open flowing track. In short technical tracks, it lacks a bit of low end grunt compared to a D4w/ HT rotor or TP Actinium
Tech Elite
iTrader: (28)
There is a V10 thread... I have tried the 13.5 in my 1/12 but have yet to find a combo that works well on 1s. Perhaps someone else has figured it out. I would imagine we would want a high RPM rotor installed to get the right feel.
Last edited by YoDog; 01-13-2015 at 08:47 AM.
Tech Elite
iTrader: (14)
Can someone post a good 13.5 boosted setup, including fdr, for a VST2? Initially tight, technical track (no turbo needed), then for another longer, faster one? Thanks
Paul
Paul
Hobbywing concentrating on more race products this year so ill keep you all posted.
Also remember guys any help you may need even for a chat please contact me on my email [email protected] or mobile +61430009769.I am approachable you know and all i care about is the customers happiness so please do not hesitate to contact me.
Also remember guys any help you may need even for a chat please contact me on my email [email protected] or mobile +61430009769.I am approachable you know and all i care about is the customers happiness so please do not hesitate to contact me.
Tech Regular
iTrader: (1)
Looking forward to the new stuff this year, just purchased a stock spec v3.1 and the programmer box to go with my v10 motor
Tech Elite
iTrader: (2)
Hobbywing concentrating on more race products this year so ill keep you all posted.
Also remember guys any help you may need even for a chat please contact me on my email [email protected] or mobile +61430009769.I am approachable you know and all i care about is the customers happiness so please do not hesitate to contact me.
Also remember guys any help you may need even for a chat please contact me on my email [email protected] or mobile +61430009769.I am approachable you know and all i care about is the customers happiness so please do not hesitate to contact me.
Regards
Rob.
Tech Adept
Tech Elite
iTrader: (13)
I've had mixed success with my v10 motor and the setting will depend a great deal what class and how you drive into.corners.
V10 doesn't have as much punch in stock trim but certainly has top end. For 13.5 blinky single cell I've had success with timing set to 40ish and a moderate rollout to track condition. I tend to use my brakes to pitch the nose in which is where I'd appreciate more punch pulling out. Some of this is esc for sure. Hobbywing esc is very smoothe to drive but having owned orca as well, orca has a slight advantage in pinchy feel I'd say. They almost feel like they have turbo but obviously don't.
Right now I'm experimenting with a higher torque rotor and modifying the endbell to get more timing. Cranking the timing on stock rotor has given it obscene top end and finally gets the motor warm heh.
Top speed has never been an issue with this motor. Its fast and runs crazy cool. I just want a little more notchiness down low.
The rotor choices are a little confusing though. I don't think 13mm is legal for roar spec but maybe the modified 5x12.5 would be as most other manufactures make rotors this size that are. I never seem to get an answer on my questions so ill just keep on keepin on.
V10 doesn't have as much punch in stock trim but certainly has top end. For 13.5 blinky single cell I've had success with timing set to 40ish and a moderate rollout to track condition. I tend to use my brakes to pitch the nose in which is where I'd appreciate more punch pulling out. Some of this is esc for sure. Hobbywing esc is very smoothe to drive but having owned orca as well, orca has a slight advantage in pinchy feel I'd say. They almost feel like they have turbo but obviously don't.
Right now I'm experimenting with a higher torque rotor and modifying the endbell to get more timing. Cranking the timing on stock rotor has given it obscene top end and finally gets the motor warm heh.
Top speed has never been an issue with this motor. Its fast and runs crazy cool. I just want a little more notchiness down low.
The rotor choices are a little confusing though. I don't think 13mm is legal for roar spec but maybe the modified 5x12.5 would be as most other manufactures make rotors this size that are. I never seem to get an answer on my questions so ill just keep on keepin on.
Tech Master
iTrader: (14)
Hey guys,
Not sure if this is the right thread but hopefully I can get some help here. I'm running a V3.1 ESC with a 21.5T in blinky mode. I'm really struggling to get decent braking. It does slow down but won't brake hard. The firmware is whatever it came with out of the box, I have not updated it at all. Will new firmware make the brakes better? What firmware version should I be using? Would greatly appreciate some help here.
Cheers
Simon
Not sure if this is the right thread but hopefully I can get some help here. I'm running a V3.1 ESC with a 21.5T in blinky mode. I'm really struggling to get decent braking. It does slow down but won't brake hard. The firmware is whatever it came with out of the box, I have not updated it at all. Will new firmware make the brakes better? What firmware version should I be using? Would greatly appreciate some help here.
Cheers
Simon
Tech Fanatic
iTrader: (35)
Hey guys,
Not sure if this is the right thread but hopefully I can get some help here. I'm running a V3.1 ESC with a 21.5T in blinky mode. I'm really struggling to get decent braking. It does slow down but won't brake hard. The firmware is whatever it came with out of the box, I have not updated it at all. Will new firmware make the brakes better? What firmware version should I be using? Would greatly appreciate some help here.
Cheers
Simon
Not sure if this is the right thread but hopefully I can get some help here. I'm running a V3.1 ESC with a 21.5T in blinky mode. I'm really struggling to get decent braking. It does slow down but won't brake hard. The firmware is whatever it came with out of the box, I have not updated it at all. Will new firmware make the brakes better? What firmware version should I be using? Would greatly appreciate some help here.
Cheers
Simon
Nice avatar by the way.
Tech Master
iTrader: (14)
Avatar is what happens when you don't clean your keyboard :P
Tech Master
iTrader: (14)
Tech Elite
iTrader: (14)