2LikesTekno RC EB48 Thread
02-05-2014 | 07:32 PM
Tech Adept
Joined: Jan 2013
Posts: 205
For the up an down movement in the spindles u might to able to take a file(flat /bastard) and file a little on the bushing. That will let u tight up on the screws and take out the extra play.
The play in the front arms I used the kyosho arm washer that come with the front or rear arms. And I shim the rear side of my front arms, I didn't have to but I did.
But the axle play needs the shim cause when u turn lock to lock the axle will just slightly rub the drive shafts when they float in but it doesn't rub when it floats out ward.
The play in the front arms I used the kyosho arm washer that come with the front or rear arms. And I shim the rear side of my front arms, I didn't have to but I did.
But the axle play needs the shim cause when u turn lock to lock the axle will just slightly rub the drive shafts when they float in but it doesn't rub when it floats out ward.
02-06-2014 | 07:24 AM
02-06-2014 | 01:01 PM
I see that the Tekno truggy shock springs come with a silver coating on them. Does anyone have the inside scoop on if Tekno is going to move to a silver coating on the buggy/sct springs? The black coating seems to come off of the current ones kind of easily. Thanks!
02-06-2014 | 01:09 PM
Hello Everyone,
As some of you may have encountered there was a batch of TKR5016B that were breaking where the tower mounted to the bulkhead.
We have just received a new batch. For anyone that has experienced a breakage of TKR5016B and still have the broken part, please follow the procedure below to receive a replacement.
You must send the warranty eligible part(s) back to us for replacement. Here is a list of what to include with your shipment:
The part(s) in question.
A note with your return address, telephone number, and email address.
Optional – any information about your setup (motor, voltage, wheels, tires, etc.). The info you provide will help us to make our products better.
Please send the above items to:
Tekno RC
ATTN: WARRANTY / REPAIR
10755 Scripps Poway Pkwy #598
San Diego CA 92131
You can speed the process along by filling out this form before sending in your parts:
http://www.teknorc.com/tekno5/wp-con...erSaveable.pdf
Once we receive your part along with the information above we will issue a coupon code via email good for 100% off of a replacement. Add the TKR5016B to your cart, go to checkout and enter the coupon code. Your discount should appear. Proceed through checkout normally and we’ll get the order processed ASAP.
Thanks for choosing our products!
Thomas,
Tekno RC Customer Support
As some of you may have encountered there was a batch of TKR5016B that were breaking where the tower mounted to the bulkhead.
We have just received a new batch. For anyone that has experienced a breakage of TKR5016B and still have the broken part, please follow the procedure below to receive a replacement.
You must send the warranty eligible part(s) back to us for replacement. Here is a list of what to include with your shipment:
The part(s) in question.
A note with your return address, telephone number, and email address.
Optional – any information about your setup (motor, voltage, wheels, tires, etc.). The info you provide will help us to make our products better.
Please send the above items to:
Tekno RC
ATTN: WARRANTY / REPAIR
10755 Scripps Poway Pkwy #598
San Diego CA 92131
You can speed the process along by filling out this form before sending in your parts:
http://www.teknorc.com/tekno5/wp-con...erSaveable.pdf
Once we receive your part along with the information above we will issue a coupon code via email good for 100% off of a replacement. Add the TKR5016B to your cart, go to checkout and enter the coupon code. Your discount should appear. Proceed through checkout normally and we’ll get the order processed ASAP.
Thanks for choosing our products!
Thomas,
Tekno RC Customer Support
02-06-2014 | 01:15 PM
-Thomas
Tekno RC Customer Support
02-06-2014 | 01:21 PM
Joined: Nov 2003
Posts: 3,595
From: Covington, La.
Hello Everyone,
As some of you may have encountered there was a batch of TKR5016B that were breaking where the tower mounted to the bulkhead.
We have just received a new batch. For anyone that has experienced a breakage of TKR5016B and still have the broken part, please follow the procedure below to receive a replacement.
You must send the warranty eligible part(s) back to us for replacement. Here is a list of what to include with your shipment:
The part(s) in question.
A note with your return address, telephone number, and email address.
Optional – any information about your setup (motor, voltage, wheels, tires, etc.). The info you provide will help us to make our products better.
Please send the above items to:
Tekno RC
ATTN: WARRANTY / REPAIR
10755 Scripps Poway Pkwy #598
San Diego CA 92131
You can speed the process along by filling out this form before sending in your parts:
http://www.teknorc.com/tekno5/wp-con...erSaveable.pdf
Once we receive your part along with the information above we will issue a coupon code via email good for 100% off of a replacement. Add the TKR5016B to your cart, go to checkout and enter the coupon code. Your discount should appear. Proceed through checkout normally and we’ll get the order processed ASAP.
Thanks for choosing our products!
Thomas,
Tekno RC Customer Support
As some of you may have encountered there was a batch of TKR5016B that were breaking where the tower mounted to the bulkhead.
We have just received a new batch. For anyone that has experienced a breakage of TKR5016B and still have the broken part, please follow the procedure below to receive a replacement.
You must send the warranty eligible part(s) back to us for replacement. Here is a list of what to include with your shipment:
The part(s) in question.
A note with your return address, telephone number, and email address.
Optional – any information about your setup (motor, voltage, wheels, tires, etc.). The info you provide will help us to make our products better.
Please send the above items to:
Tekno RC
ATTN: WARRANTY / REPAIR
10755 Scripps Poway Pkwy #598
San Diego CA 92131
You can speed the process along by filling out this form before sending in your parts:
http://www.teknorc.com/tekno5/wp-con...erSaveable.pdf
Once we receive your part along with the information above we will issue a coupon code via email good for 100% off of a replacement. Add the TKR5016B to your cart, go to checkout and enter the coupon code. Your discount should appear. Proceed through checkout normally and we’ll get the order processed ASAP.
Thanks for choosing our products!
Thomas,
Tekno RC Customer Support
02-06-2014 | 02:37 PM
-Thomas
02-06-2014 | 03:40 PM
Hello Everyone,
As some of you may have encountered there was a batch of TKR5016B that were breaking where the tower mounted to the bulkhead.
We have just received a new batch. For anyone that has experienced a breakage of TKR5016B and still have the broken part, please follow the procedure below to receive a replacement.
You must send the warranty eligible part(s) back to us for replacement. Here is a list of what to include with your shipment:
The part(s) in question.
A note with your return address, telephone number, and email address.
Optional – any information about your setup (motor, voltage, wheels, tires, etc.). The info you provide will help us to make our products better.
Please send the above items to:
Tekno RC
ATTN: WARRANTY / REPAIR
10755 Scripps Poway Pkwy #598
San Diego CA 92131
You can speed the process along by filling out this form before sending in your parts:
http://www.teknorc.com/tekno5/wp-con...erSaveable.pdf
Once we receive your part along with the information above we will issue a coupon code via email good for 100% off of a replacement. Add the TKR5016B to your cart, go to checkout and enter the coupon code. Your discount should appear. Proceed through checkout normally and we’ll get the order processed ASAP.
Thanks for choosing our products!
Thomas,
Tekno RC Customer Support
As some of you may have encountered there was a batch of TKR5016B that were breaking where the tower mounted to the bulkhead.
We have just received a new batch. For anyone that has experienced a breakage of TKR5016B and still have the broken part, please follow the procedure below to receive a replacement.
You must send the warranty eligible part(s) back to us for replacement. Here is a list of what to include with your shipment:
The part(s) in question.
A note with your return address, telephone number, and email address.
Optional – any information about your setup (motor, voltage, wheels, tires, etc.). The info you provide will help us to make our products better.
Please send the above items to:
Tekno RC
ATTN: WARRANTY / REPAIR
10755 Scripps Poway Pkwy #598
San Diego CA 92131
You can speed the process along by filling out this form before sending in your parts:
http://www.teknorc.com/tekno5/wp-con...erSaveable.pdf
Once we receive your part along with the information above we will issue a coupon code via email good for 100% off of a replacement. Add the TKR5016B to your cart, go to checkout and enter the coupon code. Your discount should appear. Proceed through checkout normally and we’ll get the order processed ASAP.
Thanks for choosing our products!
Thomas,
Tekno RC Customer Support
02-06-2014 | 09:47 PM
Tech Addict
iTrader: (11)
Joined: Jul 2011
Posts: 547
From: Trains and Lanes Easton PA
Quick questions all,
For the shocks, I am putting the bottom eyelet on each of my front shock shafts, but one eyelet bottoms out before the other leaving a difference of about 2 mm in overall shaft length, what is the proper length of the shock shaft with the eyelet seated and no piston?
Next, when the shock shaft is finished, the nut on top sticks up, should this nut touch the bladder at all?
Final, in order to potentially limit upward travel so the nut don't hit the bladder do you use limiters on the outside of the shock like the sct410?
For the shocks, I am putting the bottom eyelet on each of my front shock shafts, but one eyelet bottoms out before the other leaving a difference of about 2 mm in overall shaft length, what is the proper length of the shock shaft with the eyelet seated and no piston?
Next, when the shock shaft is finished, the nut on top sticks up, should this nut touch the bladder at all?
Final, in order to potentially limit upward travel so the nut don't hit the bladder do you use limiters on the outside of the shock like the sct410?