Novarossi engines thread
#976
Originally Posted by jca2000au
Hi... Piyo Piyo
Do you know they web site? I just send PM to you as well.
Regards,
Do you know they web site? I just send PM to you as well.
Regards,
#978
[QUOTE=THE DOCTOR]
Try Mugen USA. www.mugenracing.com
John
Originally Posted by THE DOCTOR
Anyone know where I can get a new connecting rod for my X12???
Any thoughts??
Any thoughts??
John
#979
Originally Posted by jca2000au
Hi... Piyo Piyo
Do you know they web site? I just send PM to you as well.
Regards,
Do you know they web site? I just send PM to you as well.
Regards,
Champion A ( ground floor ), Artha Gading Mall, Kelapa Gading.
This guy have lots of novarossi engines including LL3 and LL5, over 150 engines said some people.
#980
Tech Champion
iTrader: (17)
I have a Nova Rossi RX21R1WC, thru like 1/2 gallon only......with 20% fuel, however, I still don't know do I have to add shim under the head........?
The one under the head right now is the SILVER stock one, I believe it is a 0.3mm shim.......for 20%, do I have to add a 0.1mm or 0.2mm to 0.50mm?
I have seen a lot of setup (from serpent) by using 25% and their shim setup are 0.6mm to 0.65mm........and 30% are up to 0.7mm.....
I am only using 20% now.....do I need to add shim? or setup to 0.5mm total? Thanks.......
The one under the head right now is the SILVER stock one, I believe it is a 0.3mm shim.......for 20%, do I have to add a 0.1mm or 0.2mm to 0.50mm?
I have seen a lot of setup (from serpent) by using 25% and their shim setup are 0.6mm to 0.65mm........and 30% are up to 0.7mm.....
I am only using 20% now.....do I need to add shim? or setup to 0.5mm total? Thanks.......
#981
Only when you are using 30% nitro or more, then additional shim is needed to prevent early detonation, and/or to make idle better.
BTW, do you know anyone who can produce NSR S5 sleeve only ? I want to buy bunch of them.
BTW, do you know anyone who can produce NSR S5 sleeve only ? I want to buy bunch of them.
#982
Originally Posted by asw7576
Only when you are using 30% nitro or more, then additional shim is needed to prevent early detonation, and/or to make idle better.
BTW, do you know anyone who can produce NSR S5 sleeve only ? I want to buy bunch of them.
BTW, do you know anyone who can produce NSR S5 sleeve only ? I want to buy bunch of them.
#984
Tech Elite
iTrader: (1)
hi..wanna share my experience with u guys ... i had my nova S5 motor for 2 and a half years......of course piston sleeve no more/ or almost no compression....anyway other parts such as crankshaft,internal bearing and outer bearing, conrod has been replaced in that 2 years except the piston seleeve...
so b4 my club race last weekend i gave the piston/sleeve to a friend for 'pinching' .... (i have never done this b4 so decide to give it a shot) ...after that i can feel more resistance than previous. after 2 tanks sort of 'break in' i raced the motor...... wow i was really surprise , (of course thanks to my mechanic very good tuning)... the motor didnt' even dies once starting frm 3 / 5 minutes heats plus the 45 minutes main....i can feel the power ... i enjoy it ... i combine the motor with rd logis 61217 pipe, 25%gammalube fuel and no 7f nova glowplug.... thanks
so b4 my club race last weekend i gave the piston/sleeve to a friend for 'pinching' .... (i have never done this b4 so decide to give it a shot) ...after that i can feel more resistance than previous. after 2 tanks sort of 'break in' i raced the motor...... wow i was really surprise , (of course thanks to my mechanic very good tuning)... the motor didnt' even dies once starting frm 3 / 5 minutes heats plus the 45 minutes main....i can feel the power ... i enjoy it ... i combine the motor with rd logis 61217 pipe, 25%gammalube fuel and no 7f nova glowplug.... thanks
#985
grinder : thank alot men !
racbj : so pinching tool works ? I want to know how long the sleeve will last after being pinched.
racbj : so pinching tool works ? I want to know how long the sleeve will last after being pinched.
#987
Originally Posted by asw7576
Try this guy : A phing +62 21 4586 4165 or ask your relative to go to :
Champion A ( ground floor ), Artha Gading Mall, Kelapa Gading.
This guy have lots of novarossi engines including LL3 and LL5, over 150 engines said some people.
Champion A ( ground floor ), Artha Gading Mall, Kelapa Gading.
This guy have lots of novarossi engines including LL3 and LL5, over 150 engines said some people.
#988
I have a Mugen MR12 engine that is in need of new bearings. I thought there might be a Novarossi compatable bearing set for this engine?
Is there anything between the Mugen MR12 and Novarossi equivelent of this engine that will interchange? This is my first on-road engine, taking a break from Unlimited MT for a bit.
Maybe a place to get parts for it?
Any info on this would be appreciated.
Is there anything between the Mugen MR12 and Novarossi equivelent of this engine that will interchange? This is my first on-road engine, taking a break from Unlimited MT for a bit.
Maybe a place to get parts for it?
Any info on this would be appreciated.
#989
Tech Elite
iTrader: (9)
[QUOTE= I want to know how long the sleeve will last after being pinched.[/QUOTE]
from my experience it only last for 1 or 2 full day race. but dont expect the performance as good as new engine but at least it still competitive. it works well if ur sleeve is still new n in good condition..
from my experience it only last for 1 or 2 full day race. but dont expect the performance as good as new engine but at least it still competitive. it works well if ur sleeve is still new n in good condition..