JL Racing .12
#646
Tech Champion
iTrader: (3)
Guys check this link out, it will be good for a few weeks only or while supplies last !!!
http://www.kamikazercracing.com/prod...php?prod=51124
http://www.kamikazercracing.com/prod...php?prod=51124
#647
Team Kamikaze,
Just wondering what shipping service you use to Canada?
Just wondering what shipping service you use to Canada?
#648
Last day I was trying to install Kyosho 2D on my JL but I've found a problem. the clutch nut is not as firm as was the 3D flywheel.. I mean I can move the piston through flywheel normally but when I was tighten I used the flywheel pin holder tool and Hudy tool.. I tighten and with the hudy tool I was moving the crankshaft too
I tried to place a tierap on exhaust port so its stop the piston and I can tighten but it broke and this can damage the piston
I was wondering if this tool here is for lock the piston in this case
http://rc-mushroom.com/product_info....oducts_id=3771
http://www.rcmart.com/catalog/produc...ducts_id=15649
I tried to place a tierap on exhaust port so its stop the piston and I can tighten but it broke and this can damage the piston
I was wondering if this tool here is for lock the piston in this case
http://rc-mushroom.com/product_info....oducts_id=3771
http://www.rcmart.com/catalog/produc...ducts_id=15649
#649
Hi Guys,
does anyone now how much was the stock head shimms for the JLR red dot. Was it 0.50mm ???
thnx
does anyone now how much was the stock head shimms for the JLR red dot. Was it 0.50mm ???
thnx
#650
two 0.2mm and one 0.1mm
#651
#653
Tech Champion
iTrader: (3)
Last day I was trying to install Kyosho 2D on my JL but I've found a problem. the clutch nut is not as firm as was the 3D flywheel.. I mean I can move the piston through flywheel normally but when I was tighten I used the flywheel pin holder tool and Hudy tool.. I tighten and with the hudy tool I was moving the crankshaft too
I tried to place a tierap on exhaust port so its stop the piston and I can tighten but it broke and this can damage the piston
I was wondering if this tool here is for lock the piston in this case
http://rc-mushroom.com/product_info....oducts_id=3771
http://www.rcmart.com/catalog/produc...ducts_id=15649
I tried to place a tierap on exhaust port so its stop the piston and I can tighten but it broke and this can damage the piston
I was wondering if this tool here is for lock the piston in this case
http://rc-mushroom.com/product_info....oducts_id=3771
http://www.rcmart.com/catalog/produc...ducts_id=15649
#654
Tech Regular
iTrader: (11)
Last day I was trying to install Kyosho 2D on my JL but I've found a problem. the clutch nut is not as firm as was the 3D flywheel.. I mean I can move the piston through flywheel normally but when I was tighten I used the flywheel pin holder tool and Hudy tool.. I tighten and with the hudy tool I was moving the crankshaft too
I tried to place a tierap on exhaust port so its stop the piston and I can tighten but it broke and this can damage the piston
I was wondering if this tool here is for lock the piston in this case
http://rc-mushroom.com/product_info....oducts_id=3771
http://www.rcmart.com/catalog/produc...ducts_id=15649
I tried to place a tierap on exhaust port so its stop the piston and I can tighten but it broke and this can damage the piston
I was wondering if this tool here is for lock the piston in this case
http://rc-mushroom.com/product_info....oducts_id=3771
http://www.rcmart.com/catalog/produc...ducts_id=15649
#655
Just got my red dot today and I am working on installing it in my serpent now.
The spacer that went between the front bearing and collet on my NR is the wrong inner diameter.
Do I find one the right size, or run it without one?
The spacer that went between the front bearing and collet on my NR is the wrong inner diameter.
Do I find one the right size, or run it without one?
#657
Thanks for the quick reply
Thanks to Kamikaze for the fast shipping to Canada.
The engine looks SWeeeeet!
Tonight is practice night, hoping to get it running and broken in and ready for raceday
Thanks to Kamikaze for the fast shipping to Canada.
The engine looks SWeeeeet!
Tonight is practice night, hoping to get it running and broken in and ready for raceday
#658
Just bought the full kit from Sam at kamikaze. 2607 pipe, engine + manifold gasket. Even though i just bought a new engine last month, at the price your doing these, i couldn't resist.
#659
what kind of plug did it have in it when I got it, the only marking was what looked like a 1 or an L ??
Engine started right up into a good raspy idle. taking it out to run a few tanks.....
Engine started right up into a good raspy idle. taking it out to run a few tanks.....
#660
yes i have tried that pipe but it doesnt work good with the header that come with it i used the header that comes with the 2607 mega pipe and man it really give the motor lots of power