R/C Tech Forums

R/C Tech Forums (https://www.rctech.net/forum/)
-   Offroad Nitro Engine Forum (https://www.rctech.net/forum/offroad-nitro-engine-forum-157/)
-   -   EB Mods JS Engine (https://www.rctech.net/forum/offroad-nitro-engine-forum/316041-eb-mods-javascript-engine.html)

TheFcuddy 05-14-2010 08:34 PM

Just got my JS Full Mod in today from Absolutehobbyz. I bolted it up with an 086 pipe. I can't wait to run my truggy with this engine. I won't be at the Hut this weekend, going backpacking. Hopefully I can catch the next one.

toobad4u 05-14-2010 08:47 PM

I have the Full Mods in my buggy and truggy, both with the 086 pipes. These motors run great. You wont be disappointed with the combo.

Stephen

Trevor Williams 05-15-2010 09:18 AM

try the 9853/053 in truck ;)

bopracer 05-15-2010 05:00 PM

O rings
 
Hi, are the 'O' rings in the low speed and high speed needle the same size? I just put in new 'O' rings in the HSN and they were extremely tight and hard to fit and I though maybe I had the wrong size.

pballer2777 05-16-2010 05:19 PM

ran my raceprep for the first time today. all i can i say is WOW!! it's in a losi 8t 2.0 with a 7mm insert, p4 plug and 086 pipe. got 11mins. love this motor. if u r looking for an awsome piece look no futher.

wallot 05-17-2010 03:17 PM

back home with FULL mod as race prep was not available (made a huge order at amain to smuggle back home)
will try it on Wednesday with my old EB MODS 2041 pipe so I can compare (already tested JP-4 and 9901)

jpalessi 05-17-2010 04:29 PM


Originally Posted by bopracer (Post 7409345)
Hi, are the 'O' rings in the low speed and high speed needle the same size? I just put in new 'O' rings in the HSN and they were extremely tight and hard to fit and I though maybe I had the wrong size.

yes the orings for the carb needles are the same size. 005

yotasan 05-17-2010 05:22 PM

EB Mods Race Prep
 
need some help, does anyone know what the baseline settings are for a EB Mod Race Prep engine?

THANKS. :confused:

Shoaf85 05-17-2010 05:57 PM

Joe did you get my messages?

jpalessi 05-17-2010 06:23 PM


Originally Posted by Shoaf85 (Post 7418612)
Joe did you get my messages?

Yes, email replied.

jpalessi 05-17-2010 06:25 PM


Originally Posted by yotasan (Post 7418431)
need some help, does anyone know what the baseline settings are for a EB Mod Race Prep engine?

THANKS. :confused:

Set the idle gap @ 1-1/4 turns in from JUST closed. be precises.
The HSN & LSN start at 1/2 turn in from flush.

yotasan 05-17-2010 06:54 PM

Race prep
 
Thanks Joe.. Will try base settings tomorrow...

icemandolmite 05-17-2010 07:25 PM

HEY JOE CAN I GET THAT INVOICE:weird::weird:

bopracer 05-17-2010 09:55 PM


Originally Posted by jpalessi (Post 7418158)
yes the orings for the carb needles are the same size. 005

Thanks Joe

Joey Erwin 05-17-2010 10:24 PM

I have been reading through all the post and just wanted to give my input and expierence with the JS EBmods motor.
1st off Peter Marten from TKO has been so helpful and has taught me alot over the past few weeks out at Revelation Raceway racing and testing.
I am currently running both Race Prep engines in my buggy and truggy.

My buggy is getting over 9 mins of run time at Rev and 11 at Hot Rod Hobbies(smaller track) The motor is super linear and smooth just rolls off the bottom and has no problem clearing the massive Triple at Rev from the inside line.
I am running an p4 plug, 086 pipe and EBmods 30% fuel. Idles like a champ consistant tune and pulls everyone down the straight.
Did i mention i have 5 gallons on this thing!!!!!

If you race at Revelation and need any help with your JS let know.


All times are GMT -7. It is currently 09:18 AM.

Powered By: vBulletin v3.9.3.9 Patch Level 3
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.