Need a motor
 

Hi I need a go tech dealer in the USA!! Names and numbers, can anyone help??

22 racer will help you out pm him

Sounds about right we had to wind the LSN in the same amount from the factory. The HSN is very touchy........ we run the HSN on our MG 66's flush with maybe an hour either way.

We only idled ours for about 1min (just to warm it up) then straight on the track at about 90% race tune (we call it the honeymoon period for the first tank). Then over the next 3 -4 tanks we increase to full race tune.

Since then this engine has done 10 litres still has grreat compression at TDC, no slop on the conrod and between 9 - 10 min runtimes from a buggy.

Cheers

Mark

Anyone have any luck getting ahold of the new Us distributor yet?

Rex

Hi Megacrash.
+1 on those settings.
Both needles will vary a little with fuel, pipe, climate etc - HSN around flush is pretty close. I had to go in on the LSN about the same for a rich but clean take off for run in.
London eh - Hmmm the MG66 is global for sure :)

#1831 of 1831 by Ruune (ruune) on Mon Sep 14 20:55:50 2009:
Hey Guys, Sorry about the late entrance. I'm trying to finish the pricing tonight, and then get things rolling with placing the initial order w/ the factory. To clear things up: Yes, we will be offering a limited number of sponsorships- both full and partial. For the team members that havent contacted me already, I need you to contact me no later than WEDNESDAY OCT. 23rd, 2009. I plan to have the first order in with the factory by then. All of the full sponsorships will need to be verified through the factory. Parts. I've heard a lot of complaints from customers and dealers that there weren't enough parts available- specifically conrods, rebuild kits (sleeve, piston, rod), and carbs. I will be stocking rods as a separate item, plus full rebuild kits and replacement carbs. Having spent the better part of my 20's (I'm 33 now) in tech support, I know you cant support a product without parts. I cant promise that I'll have everything right off the bat, but I plan to have the most commonly needed items. Something was mentioned above regarding carburetors- the new GX carburetors are a new design, but are not backwards compatible. Mike Clark... I'll be at RC Pro this weekend. We'll talk then. Tmizz... ask Pato for my MSN address and give me a shout. Availability. I will be offering engines and parts through both online retailers and local hobby shops. If you want your LHS to carry the new engine line, have them contact me ASAP at [email protected]. I've already talked to Kendall about filling backorders for amain, so they'll obviously be available through amain hobbies. I feel that online retailers and local hobby shops are essential to supporting our customers, and will be working to make sure that pricing and availability provided equally to both types of dealers. I look forward to working with you guys and breathing new life into the go engine line, here in the US. Sincerely, Trey Morrow Go Engine USA [email protected]



--------------------------------------------------------------------------------

That's great news for GO !!!

Looks like all my GO forum buddies in the US won't have to wait much longer for all the good stuff :) :D

Hey guys,
Glad to hear from you all. I'm getting a TON of email, trying to answer it all, and make headway in getting this thing off the ground.

Anyways, I've been working on the pricing structure for dealers and trying to figure the best parts to stock up on. So, I figured that this would be a good place as any to pose the question.

For those of you awaiting parts, what are you waiting on? On my list, I've got conrods (duh, and lots), a couple of cranks, piston/pin/sleeve/rod kits, a few carbs- both old and new (GX carbs dont work with the older models), various seals, bearings, etc.

Anything else?

Also, have your dealers contact me! I'm planning on placing the first order next week, and I want to be as inclusive off the bat as I can!

As for the website, I'm going to be putting up an informational site, then relying on dealers and online retailers for delivery. This way I can concentrate on the business at hand, rather than spending days coding a new site.

Only things that spring to mind are some seperate supplies (other then the PRS sets) of the TiNi wrist pins and some sets of wrist pin clips, as a lot of guys like to change the pin and clips when they throw a new rod in. Couple of spare cooling heads and some turbo buttons in case of the odd stripped plug thread. That should do it I reckon. Best wishes for success in your new venture. It should be a no brainer, as the GO's sell themselves :)

it sounds like its all go ahead in the states :nod:

Hi everyone,

I got the 7p Gotech older version no mod, After running it in a race I open up the engine cleaned it up and when I was trying to fix it back the cornrod would't turn, I think its bend . How could this be ? :confused::confused:

Another thing, could I use rubber grease to Lubricate all the o ring on the needles ?:D:D

You didn't put the con rod piston in back wards? If it worked when you took apart should work when you put back together. Is the crank all the way in? Do you have the sleeve set in correctly? I use dish washing soap to install my seals. It dries up and will not crack the seals.

Thats good to hear,

Ill try to get around 9 tanks through mine before it hits the track its done 4 now all at a steady 210-230 so im happy so far :D

i to think it sounds like the crank is not all the way in and the backing plate is hard against it