Hey Malik, have you had a chance to try that PT Mods 5 port in your D8 yet?

rc lover - here is a thread I posted on the Australian GO forum a couple of days ago. Should answer your questions.

"Any of the stock Go Pro motors 3, 5, or 7 port will suit buggy, it all depends on the track type you run.
5 Port has massive bottom end and good top
7 Port has good bottom end and massive top
3 Port is nippy throughout the range

I have a soft spot for the 7 Port in a buggy. It suits most tracks pretty good in stock form. Run it with 2047 pipe for longer open track or 0801 pipe for a shorter and tighter track. If you want a budget pipe that works well in most conditions on the 7 port, go for the Dynamite 053."

In addition to this, the 3 Port works well with the 0801 or Dynamite 086.
The 5 Port with 0801 or Dynamite 086 also.
The 0801 pipe gives better economy in general (and is a sweet performer).
If you run the 7 mm restrictor (or 6.5) and drive smooth you should get 10 mins or very close to it out of any of the 3 Pro series motors.

As far as where to get these motors - you don't say where you are in "the world" so I will take a stab in the dark and assume you are in the USA. There are a couple of GO dealers on this forum. Contact Rocket42 or Brain at Pro Twister Mods. If you are Southern hemisphere, contact Mark at Massive Mods in Australia.

go- tech engine
 

Hey griz thank man i am in the usa as a matter of fact i leave in Raleigh,nc but again thanks i think i will go with a couple of the go engines for truggy and buggy.:nod::nod::nod::nod::nod::nod::nod:


Xray baby

I would say 7 port in buggy and 5 port in truggy.

http://www.carolinasrc.com/Webstore/...idcategory=318

This place has the go engines right in the same State

Sorry man all out of stock

amain.com has them in stock

Another USA dealer

http://www.modhobby.com/catalog/shopbybrand/gotech

Hope this helps ya

Right on :nod:

I would get a motor from one of the guys on this forum. They both offer great after sales service, and are very knowledgeable regarding the GO products. Try a PM to Rex "22 Racer" or Brian "Mugen46" and keep it in house :)

Don't forget Mark "MassiveMods" if you are down in the lower half of the world.;)

Does any Go dealer have a Go .21 Rod in stock? or anyone that may want to sell it, thanks.

They still have the 3-ports for $99....

I use to run GO's but have since switched to a different mill and i have a new .21 con rod in the pkg. Pm me if your interested.

replying to your PM...

Hey RC lover! I have a video that you can listen to my "stock" GO7Port turbo

ok Its an 808 with
GO 7port turbo
77t odn plug
30% TQ fuel
Hong Nor 053
xray stock alum shoes
1.1 mugen springs
stock gearing
panther K2's with one peeling off lol hence the spin out/pipe jump lol

http://www.youtube.com/watch?v=Wc5Hx7hY3vM

And yes Xray baby!!! lol :nod:

go- tech engine
 

Hey Guys thanks for all the help and web stuff i will go with the 3 port for buggy and the five port for the truggy got intouch with both rocket42 and brian pro twister mods so again thank for all the help will keep it in the fam of rc support. :tire::tire:===:tire::tire:====:nod::nod::nod::nod ::nod::D:D:D:D:D