Serpent 960....
#1666
Tech Master
iTrader: (2)
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Originally Posted by going4#1
Anyone using the new ackerman set? I notice there is a lot of play between the set and the upper radio plate. I've stuck in a washer to help remove some of it but I was wondering if there was a method that didn't require extra parts.
There is a washer that is suppose to sit on top of the center post. It is machined out on one side. It is part # 902152 - radio plate spacer.
#1667
Tech Regular
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Does anyone have an effective method for keeping the grub screw from coming loose from the aluminium brake pulley? I've tried locktight but it still gets loose. Very frustrating.
Thanks in advance.
Thanks in advance.
#1668
Tech Adept
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
going4#1 Does anyone have an effective method for keeping the grub screw from coming loose from the aluminium brake pulley? I've tried locktight but it still gets loose. Very frustrating.
Never had one come loose this way.
#1669
Tech Adept
iTrader: (1)
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Originally Posted by sn4il
Hi.
How do You guys setup Your track width on 960 using Hudy Tweak Station??
My tweak station shows around 205mm (rear) instead 260-262?
What am I doing wrong?
Thnx
sn4il
How do You guys setup Your track width on 960 using Hudy Tweak Station??
My tweak station shows around 205mm (rear) instead 260-262?
What am I doing wrong?
Thnx
sn4il
Don't worry, you are not doing anything wrong. Your Hudy Station is working just fine. There is a 20mm offset for the front wheels and 30mm offset for the rear.
example: 205mm in the rear on the Hudy Station is a trackwidth of 265mm with the rear wheels installed on the car. (205+30+30=265)
example: 205mm in the front on the Hudy Station is a trackwidth of 245mm, with the front wheels installed on the car. (205+20+20=245)
Hope this helps.
#1670
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Hope this helps.
This is exactly what I was looking for.
#1671
Tech Regular
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Originally Posted by Bob The Builder
I used two shorter grub screws - put one in and tighten it down - then follow the first one with another grub screw and lock them together.
Never had one come loose this way.
Never had one come loose this way.
#1672
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Originally Posted by emankov
Hi all
Sorry for my noobness but i have a small question regarding 960 assembly...
After completion of step 1.5, i have an horizontal "endplay" of the axle, of about 0.3 mm..Is this normal, or the axle should be rock solid with no horizontal movement watsoever?
Thanks
Sorry for my noobness but i have a small question regarding 960 assembly...
After completion of step 1.5, i have an horizontal "endplay" of the axle, of about 0.3 mm..Is this normal, or the axle should be rock solid with no horizontal movement watsoever?
![weird](https://www.rctech.net/forum/classic_images/smilies/weird.gif)
Thanks
#1673
Tech Apprentice
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
it was nice to see Chris Verano out this weekend running a 960 after his 2 month off of 1/8 he still has it. he should do well at the Kyosho race
Bryon
Bryon
#1674
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Any of you guys heading to Cincinnati for the 1/8 Nationals in October?
#1675
Tech Adept
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
going4#1
Bob, the shortest grub screw I can find is 3mm long x 4 mm wide. Are there grub screws 2mm x 4mm?
Bob, the shortest grub screw I can find is 3mm long x 4 mm wide. Are there grub screws 2mm x 4mm?
#1676
Tech Regular
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
guys!
have you seen those "new" parts that has been released?
http://www.mytsn.com/products/
the new lightweight steel middle axle...
the new wishbones.. etc..
have you seen those "new" parts that has been released?
http://www.mytsn.com/products/
the new lightweight steel middle axle...
the new wishbones.. etc..
#1677
Tech Regular
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Originally Posted by Orfeous
guys!
have you seen those "new" parts that has been released?
http://www.mytsn.com/products/
the new lightweight steel middle axle...
the new wishbones.. etc..
have you seen those "new" parts that has been released?
http://www.mytsn.com/products/
the new lightweight steel middle axle...
the new wishbones.. etc..
#1678
Tech Regular
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
yes, that should be nice
![Big Grin](https://www.rctech.net/forum/classic_images/smilies/biggrin.gif)
#1679
Tech Regular
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Anyone using the new fuel lid? Anyone getting a leak? After putting on the new lid my fuel tank now leaks from the rear of the new lid. The leak isn't super serious but I'd rather not have it. Any solutions? When is the new 125cc with silcon ring lid coming out?
#1680
Suspended
![Default](https://www.rctech.net/forum/images/icons/icon1.gif)
Originally Posted by Orfeous
no, it isnt enough..