Mugen MTX-3
08-18-2004, 10:01 AM
Tech Apprentice
Originally posted by Mugen Power
oh...i just get a GP 800mah to make Reciever Batt by DIY!
So Easy....Cheaper than the Sanyo one by ......50%offˇI
oh...i just get a GP 800mah to make Reciever Batt by DIY!
So Easy....Cheaper than the Sanyo one by ......50%offˇI
still need cycle~
i may try to cycle one times....see see how much MAH can it have!
08-19-2004, 12:57 AM
need urgent helps.
I am halfway thru building a kawahara neg diff.
Does anyone know where the red o ring goes. Cause I can't work it out ?
Thanks
I am halfway thru building a kawahara neg diff.
Does anyone know where the red o ring goes. Cause I can't work it out ?
Thanks
08-19-2004, 01:02 AM
sorry Y, dont know. been a couple months since i built mine. try matching it up on the instructions.
08-19-2004, 01:05 AM
I did that but can't see where it goes. Cause you use the ones that come out of the normal diff
An i have this one red o ring left over
An i have this one red o ring left over
08-19-2004, 01:57 AM
Tech Fanatic
sure it goes between the diff housing and showe housing
08-19-2004, 02:22 AM
Originally posted by Cartman
sure it goes between the diff housing and showe housing
sure it goes between the diff housing and showe housing
08-19-2004, 02:25 AM
Originally posted by Ybakoff
This may sound stupid but what is a showe housing ?
This may sound stupid but what is a showe housing ?
08-19-2004, 04:04 AM
Originally posted by chippy
shoe housing
shoe housing
Maybe I have disabled instructions
08-19-2004, 06:20 AM
Hmmm . . . we use a Neg. Diff on a Kyosho Evo and I guess it must be similar. The main thing to worry about is insuring you keep the diff oil away from the clutch shoes, yeah?
Does this look right?
Does this look right?
08-19-2004, 01:46 PM
MTX-3 tire sizes...?
It's been a while since I've had to buy new tires. Just want to make sure I'm getting the right sizes...:
It's 0 offset FRONT
2 deg offset REAR
right?
It's 0 offset FRONT
2 deg offset REAR
right?
08-19-2004, 01:48 PM
Re: MTX-3 tire sizes...?
Per manual, it should be ALL offset.
I've been running mine with wheel spacer, so I can use anything I can get.
best,
I've been running mine with wheel spacer, so I can use anything I can get.
best,
Originally posted by j240z
It's been a while since I've had to buy new tires. Just want to make sure I'm getting the right sizes...:
It's 0 offset FRONT
2 deg offset REAR
right?
It's been a while since I've had to buy new tires. Just want to make sure I'm getting the right sizes...:
It's 0 offset FRONT
2 deg offset REAR
right?
08-19-2004, 09:01 PM
Eddie,
Would you happen to know what a negative diff would go for used? I found one but not sure what condition it is in. Let me know what you think......I think it is 6 to 8 months old.....Is the negative diff worth it?
Would you happen to know what a negative diff would go for used? I found one but not sure what condition it is in. Let me know what you think......I think it is 6 to 8 months old.....Is the negative diff worth it?
08-19-2004, 09:10 PM
Re: Re: MTX-3 tire sizes...?
Originally posted by eddiethefish
Per manual, it should be ALL offset.
I've been running mine with wheel spacer, so I can use anything I can get.
best,
Per manual, it should be ALL offset.
I've been running mine with wheel spacer, so I can use anything I can get.
best,
08-19-2004, 09:23 PM
Also, where can I get some wheel spacers? It seems it would be easier to be able to use any offset wheel.
BTW I have the Kawahara wheel hexes, if that makes a difference...?
BTW I have the Kawahara wheel hexes, if that makes a difference...?
08-19-2004, 11:51 PM
Depends.
If you are running 24mm or 26mm wheels(for rubber) then you dont need spacers. If you run regular offset 30mm wheels then you will need spacers.
If you are running 24mm or 26mm wheels(for rubber) then you dont need spacers. If you run regular offset 30mm wheels then you will need spacers.