Mugen MTX-3
05-10-2004, 04:40 PM
Tech Initiate
Even pressure
Originally posted by *_DeckeR_*
HAHAHA, is a pressure chamber a boost bottle??
if it is they do nothing to enhance the performance of your motor, they just lean ya motor out making harder to tune and inconsistent.
just get a proffessional to start puttin a cupla holes in ya piston and liner, but dont touch the crank cuz it will never be balanced after u touch it
HAHAHA, is a pressure chamber a boost bottle??
if it is they do nothing to enhance the performance of your motor, they just lean ya motor out making harder to tune and inconsistent.
just get a proffessional to start puttin a cupla holes in ya piston and liner, but dont touch the crank cuz it will never be balanced after u touch it
05-10-2004, 04:45 PM
Re: Even pressure
Originally posted by DocSafety
Actually it's supposed to insure even pressure throughout the entire tank load so it DOESN'T lean out at the end of the run
Actually it's supposed to insure even pressure throughout the entire tank load so it DOESN'T lean out at the end of the run
05-10-2004, 04:46 PM
I meant the between the fuel tankand carb.
05-10-2004, 04:50 PM
Hey Guys,
So how gearing ratio affect tire diameter?
So how gearing ratio affect tire diameter?
05-10-2004, 05:18 PM
Do I need to drill a hole in the top plate to install the chamber mounting bracket?
05-10-2004, 06:08 PM
pimp,
you're too organized.
you're too organized.
Originally posted by Nitropimp
No just use the screw holding your belt tensioner. This is how I did mine.
No just use the screw holding your belt tensioner. This is how I did mine.
05-10-2004, 06:10 PM
He should have installed this underneath the upper deck.. Remember lower the CG 
05-10-2004, 06:12 PM
LCG freak?
Originally posted by Varuth
He should have installed this underneath the upper deck.. Remember lower the CG
He should have installed this underneath the upper deck.. Remember lower the CG
05-10-2004, 06:26 PM
Originally posted by eddiethefish
LCG freak?
LCG freak?
05-10-2004, 07:02 PM
Tech Master
Re: Re: Re: Re: Pressure Chamber
Originally posted by DocSafety
Do I need to drill a hole in the top plate to install the chamber mounting bracket?
Do I need to drill a hole in the top plate to install the chamber mounting bracket?
05-10-2004, 07:29 PM
you're too organized.
He should have installed this underneath the upper deck.. Remember lower the CG
05-10-2004, 07:32 PM
Originally posted by Nitropimp
You're funny Fish. A couple more days to PAYDAY. And I get my 4mm Piranah chasis. YEAH.
Yeah... your right but it looks cool up there.
You're funny Fish. A couple more days to PAYDAY. And I get my 4mm Piranah chasis. YEAH.
Yeah... your right but it looks cool up there.
05-10-2004, 08:02 PM
Tech Adept
Piranah chasis? Sounds kinda fishy to me.
Post some pics please, as I have never heard of this chassis.
Post some pics please, as I have never heard of this chassis.
05-10-2004, 08:14 PM
Tech Adept
gearing
Anyone here can give me a starting point for 0.8 gearing for a 175 ft x 90 ft track with an everchanging infield?
05-10-2004, 09:06 PM
Tech Initiate
Thanks
Originally posted by Nitropimp
No just use the screw holding your belt tensioner. This is how I did mine.
No just use the screw holding your belt tensioner. This is how I did mine.