Kyosho v-one rrr
#691
Oh yeah huh! That's rediculous! Your car practically drove to Vegas and back on Sunday. Can you post your setup?
#693
Tech Elite
iTrader: (1)
Re: TANK
Originally posted by jwf-ronni
Actually, a few of the guys used and played around with my car
for another half an hour or so after the mains. Believe or not, we
put in another battery pack on the car so they could keep on
running it. And the only time we pulled it in was when they said:
"Man this car has a bad push !"
Well, it was pushing because it was not running with JACO Tires...
it had JACO Plastic RIMS !!
Actually, a few of the guys used and played around with my car
for another half an hour or so after the mains. Believe or not, we
put in another battery pack on the car so they could keep on
running it. And the only time we pulled it in was when they said:
"Man this car has a bad push !"
Well, it was pushing because it was not running with JACO Tires...
it had JACO Plastic RIMS !!
Where can I get those JACO Plastic RIMS??
#694
Originally posted by Racing4Evo
My car wasn't working until the first main Sunday. I didn't start the first qualifier and I only ran 2 minutes in the second. The car was good, I just didn't get a chance to qualify it. The motor I planned to use, broke on Saturday and I was forced to use the O.S.
Yeah, tell me about the car being a TANK! Our cars went through 80 minutes of racing each.
My car wasn't working until the first main Sunday. I didn't start the first qualifier and I only ran 2 minutes in the second. The car was good, I just didn't get a chance to qualify it. The motor I planned to use, broke on Saturday and I was forced to use the O.S.
Yeah, tell me about the car being a TANK! Our cars went through 80 minutes of racing each.
Ron, thanks again for the turnbuckle rod. I think I fund the Ti ones and I will give it back when I return in December. What roll center did you finally decide to use for the main?
Anyone tried the Kawahara tires? I ran a set yesterday and they work great.
#695
Tech Fanatic
anyone have an overdrive calculator (spreadsheet)? thanks.
#696
Originally posted by joemugen
anyone have an overdrive calculator (spreadsheet)? thanks.
anyone have an overdrive calculator (spreadsheet)? thanks.
#697
Tech Fanatic
also, does anyone have a stock setup sheet in english?
#698
Originally posted by joemugen
also, does anyone have a stock setup sheet in english?
also, does anyone have a stock setup sheet in english?
#699
Originally posted by joemugen
also, does anyone have a stock setup sheet in english?
also, does anyone have a stock setup sheet in english?
#700
Tech Fanatic
jeffreylin, thanks a bunch man. tomorrow i am going to race this car for the first time. i am looking forward. any tips?
#701
Originally posted by joemugen
jeffreylin, thanks a bunch man. tomorrow i am going to race this car for the first time. i am looking forward. any tips?
jeffreylin, thanks a bunch man. tomorrow i am going to race this car for the first time. i am looking forward. any tips?
#702
[i]Anyone tried the Kawahara tires? I ran a set yesterday and they work great. [/B]
#703
Tech Fanatic
good advice jeff. i just got done setting my car up--- and it did not go to well. i am getting a lot of binding on the front and back end. i was told not to do the drilling out--- that after a run or two they would get worn in and the binding would go away. i hope--- i had a hell of a time trying to get this car set up. hope all is well.
#704
You shouldn't worry too much about the binding. It's not as bis a deal as electrics. Just give it time to free up. I actually prefer the car to be a little tight so that it doesn't develop a serious amount of slop over time.
#705
Tech Fanatic
thanks. that is what my hobby shop told me. i was driving the mtx-3. i do not know if you know about this or someone might, but chaning the droop is much different in the rrr. in the mtx-3 in the front, i first set the left side with the set screw, then i set the right side with the plastic piece that swivels and that was pretty much it. with this one, they have the plastic piece that swivels on both arms, plus set screws on both arms. any advice? thanks.