Kyosho v-one rrr
#4366
Tech Master
iTrader: (49)
Originally Posted by rcrossco_1
Your car looks like its been wired up by a chimpanzee.
Ive never had switch failure, maybe thats because I look after my car/s.
Heres some real wiring.............
Later....... enjoy crashing.
Ive never had switch failure, maybe thats because I look after my car/s.
Heres some real wiring.............
Later....... enjoy crashing.
I'm glad that you have never experienced a switch failure, the car being turned off due to a collision or a marshall inadvertantly turning your car off when he tries to do his job. But I have and so have a lot of other people I know who now don't use a switch as it just eliminates one more thing that can go wrong.
I wish I could trust a switch as it would be convenient but you learn from your mistakes, so no switch.
Last edited by Craig1; 12-09-2005 at 12:34 PM.
#4367
R/C Tech Elite Member
iTrader: (47)
Originally Posted by Francis M.
for crystal it should be a good starting point with rev you will probably have to go to harder tires around this time with the cold weather.
#4368
Tech Elite
iTrader: (2)
Originally Posted by Randy Caster
I'll have the right tires for both tracks, basically just wondering how good the setup is..
sorry, misread the post the RRR kit setup shouldn't be too far off for both tracks. the only thing you would probably want to adjust is the droop settings. flatter for rev and oposite for crystal.
#4369
Originally Posted by Randy Caster
I'll have the right tires for both tracks, basically just wondering how good the setup is..
#4370
Originally Posted by Randy Caster
I'll have the right tires for both tracks, basically just wondering how good the setup is..
#4371
Originally Posted by Craig1
I don't want to interupt with the arguement there but crashing is something Kyle doesn't do a lot of and as for car prep, you'd go a long way to find someone better.
.
.
Cheers
#4373
Tech Adept
Originally Posted by AndyT ©
I`ll second that.....I`d rate Kyle up there in the top echelon of racers in this country and you dont get to that level by not having an understanding of how to wire/setup/ etc etc a car.
Cheers
Cheers
Ok guys, no problems.
But there are others in this world too that know their stuff !
As with most stuff in life.... its each to thier own.
Ross
#4374
Tech Elite
iTrader: (11)
Hey Guys...
Couple of questions for you today
1st... I am using a Futaba 9550 low profile servo for the steering and i have used the 1mm spacer behind the servo. I noticed today that at the end of the travel the servo horn seems to rub on the top deck??? Should i have used the 2.5mm spacer instead?
2nd...
As i am going to be running on rubbers tyres, i have changed the front pulley over to the 24T with the corresponding belt... But it is very loose, and i am worried about it skipping.
Look forward to seeing some responses..
BB
Couple of questions for you today
1st... I am using a Futaba 9550 low profile servo for the steering and i have used the 1mm spacer behind the servo. I noticed today that at the end of the travel the servo horn seems to rub on the top deck??? Should i have used the 2.5mm spacer instead?
2nd...
As i am going to be running on rubbers tyres, i have changed the front pulley over to the 24T with the corresponding belt... But it is very loose, and i am worried about it skipping.
Look forward to seeing some responses..
BB
#4375
Tech Master
iTrader: (4)
Originally Posted by Bundy_Bear
Hey Guys...
Couple of questions for you today
1st... I am using a Futaba 9550 low profile servo for the steering and i have used the 1mm spacer behind the servo. I noticed today that at the end of the travel the servo horn seems to rub on the top deck??? Should i have used the 2.5mm spacer instead?
2nd...
As i am going to be running on rubbers tyres, i have changed the front pulley over to the 24T with the corresponding belt... But it is very loose, and i am worried about it skipping.
Look forward to seeing some responses..
BB
Couple of questions for you today
1st... I am using a Futaba 9550 low profile servo for the steering and i have used the 1mm spacer behind the servo. I noticed today that at the end of the travel the servo horn seems to rub on the top deck??? Should i have used the 2.5mm spacer instead?
2nd...
As i am going to be running on rubbers tyres, i have changed the front pulley over to the 24T with the corresponding belt... But it is very loose, and i am worried about it skipping.
Look forward to seeing some responses..
BB
i have used both futaba s9550 and s9451 and the 2.5 mm spacer works best as it gives enough clearance from the top deck opening.
i to am using the 24T side pulley but i run foams and i use the 387T belt and although it does seem abit loose but really its fine as when the car is being acccelerated the belt actually tensions as it rotates. Some will tell you to run the side belt as loose as possible to free up the car, a more efficent drivetrain equals more top speed, better fuel economy and lower engine temps
#4376
Tech Elite
iTrader: (6)
Originally Posted by tommi
Thanks again, I just tried driving with the stock setting at Glenmarie yesterday night, the track wasn't 100% dried after a light drizzling, but the car handled great. Will try out different setups thru time, but at the moment, based on the outcome of my run yesterday, I gotta stick with the one-way for a while to figure out the best setup and the dynamics of it. Are u still with the NTC3?
#4377
hey people, i got my RRR for sale for anyone interested, have a look cause its pretty cheap!:
http://www.rctech.net/forum/showthread.php?t=93435
http://www.rctech.net/forum/showthread.php?t=93435
#4378
Tech Rookie
hello out there, this is victor from madrid-spain, this is my first post and i want to say hi to all you, so, i want to know where i can to find the
K FACTORY optionals parts for my RRR:
http://www.kfactoryracing.com/prolis...01120805-97109
these parts are hard to find here in spain, please if anybody got these optional parts, let me know where found them, wich shop ?
thats all for the moment, thanxxxx
K FACTORY optionals parts for my RRR:
http://www.kfactoryracing.com/prolis...01120805-97109
these parts are hard to find here in spain, please if anybody got these optional parts, let me know where found them, wich shop ?
thats all for the moment, thanxxxx
#4379
Tech Master
iTrader: (1)
Originally Posted by tifosi_es
hello out there, this is victor from madrid-spain, this is my first post and i want to say hi to all you, so, i want to know where i can to find the
K FACTORY optionals parts for my RRR:
http://www.kfactoryracing.com/prolis...01120805-97109
these parts are hard to find here in spain, please if anybody got these optional parts, let me know where found them, wich shop ?
thats all for the moment, thanxxxx
K FACTORY optionals parts for my RRR:
http://www.kfactoryracing.com/prolis...01120805-97109
these parts are hard to find here in spain, please if anybody got these optional parts, let me know where found them, wich shop ?
thats all for the moment, thanxxxx
try rcmart.com or shopping.rcmodel.hk
they ship anywhere around the globe and they're the cheapest place you can find hop-ups for Asian products.
#4380
Originally Posted by spawn
Yup, still with my NTC3. Still working well for me. Tips, when driving 1 way, brake earlier and also power out earlier. Dont pump the gas like pink, do it smoothly and very importantly to take good racing line. Before running in a race, walk around the track or plan your racing line before racing.