R/C Tech Forums - View Profile: 1995 Monster T
R/C Tech Forums

Go Back  R/C Tech Forums > Members List
Reload this Page >

1995 Monster T's Profile

Register
FAQ
Community
Wiki Posts
Calendar
Today's Posts
Search
Vendor Directory

1995 Monster T 1995 Monster T is offline

Tech Addict

Last Activity: 04-24-2024 05:44 AM

About Me

  • About 1995 Monster T
    Country of Residence
    US
    Gender
    Male
  • Signature
    True Owner of the worlds lightest 1/5 monster truck @ 55 lbs.

Statistics

Total Posts
General Information
  • Last Activity: 04-24-2024 05:44 AM
  • Join Date: 04-23-2021
  • Referrals: 0

Likes Received

57 Likes
  1. Mac The Knife
    Mac The Knife liked post by 1995 Monster T On thread : Looking for someone who can 3d print gears
    finally found someone to print my nylon gears for the USA-1 electric first gen truck. Etsy.com. Stay away from seller: vintage_gears on ebay. He never followed through with making the parts for me...
    Liked On: 01-26-2023, 05:46 AM
    Posted On: 01-25-2023, 01:05 PM
  2. flymetonight liked post by 1995 Monster T On thread : new 2023 Primal RC 1/5 Scale Grave Digger Monster Truck WORLDS LARGEST
    It was a great idea for someone to try and build a production truck again but Primal went to china The quality and design sucks. The stock scooter motor cost $50 to replace and has now power The...
    Liked On: 01-23-2023, 09:06 AM
    Posted On: 01-22-2023, 06:25 AM
  3. flymetonight liked post by 1995 Monster T On thread : new 2023 Primal RC 1/5 Scale Grave Digger Monster Truck WORLDS LARGEST
    All the trucks have the same quality problem, cheap aluminum grade parts than meltt or brake off. A cheap motor with no power and the truck is over geared overweight. At 80 lbs. is a tank . Looks...
    Liked On: 01-21-2023, 11:16 PM
    Posted On: 01-21-2023, 01:07 PM
  4. TimothyMcConnor liked post by 1995 Monster T On thread : New tx problems
    Make sure transmitter and rx are bind first. Then esc. 未命名 -1 (flycolor.net) (http://en.flycolor.net/uploadfile/201710/0ce697a80a.pdf) follow instructions but disconnect one motor wire.
    Liked On: 01-19-2023, 08:25 AM
    Posted On: 12-27-2022, 09:16 AM
  5. TimothyMcConnor liked post by 1995 Monster T On thread : New tx problems
    make sure channel 2 is functioning with servo If it works with servo then it should work with esc Reprograming ess has nothing to do with problem.
    Liked On: 01-19-2023, 08:25 AM
    Posted On: 12-21-2022, 06:32 AM
  6. asciibaron liked post by 1995 Monster T On thread : AYK Radiant small chain tension
    The original chain length was fine before you removed the link. Ladder chain stretches and becomes loose over time from the torque of the motor. If you can order a replacement, do so. If you can't...
    Liked On: 11-11-2022, 11:43 AM
    Posted On: 11-09-2022, 05:50 AM
  7. Jaredf liked post by 1995 Monster T On thread : Tuning Woes
    First you start with factory settings to get the engine started. Usually, these settings are rich. Set the ide so the engine will stay running and then adjust the low to set the response. by bogging...
    Liked On: 10-29-2022, 07:09 AM
    Posted On: 10-29-2022, 05:53 AM
  8. Bud liked post by 1995 Monster T On thread : Moving from NIMH to LIPO
    If you're going to switch to lipo go brushless. More power and no more changing brushes or replacing motors.
    Liked On: 10-24-2022, 10:50 AM
    Posted On: 10-12-2022, 02:08 PM
  9. Stepchild liked post by 1995 Monster T On thread : T-maxx or Revo
    Consider buying a good used truck T maxx . Easier to work on and tons of options for parts. Don't waste the money on a new truck when you're going to have to go through it to make sure it's set up...
    Liked On: 10-24-2022, 08:36 AM
    Posted On: 10-18-2022, 01:19 PM
  10. Zac_with_no_K
    Zac_with_no_K liked post by 1995 Monster T On thread : How to shop for screws
    For hardware I go to ebay and buy bulk/
    Liked On: 10-16-2022, 04:51 PM
    Posted On: 10-14-2022, 12:41 PM
  11. Horatio
    Horatio liked post by 1995 Monster T On thread : How should engine bearings feel?
    I have never seen a new engine in 30+ yrs. with bad bearing from the start.. I suggest you contact the manufacture and get new replacement bearings. The symptoms you describe are common in used...
    Liked On: 10-10-2022, 10:36 AM
    Posted On: 08-09-2022, 08:24 AM
  12. Horatio
    Horatio liked post by 1995 Monster T On thread : How should engine bearings feel?
    No engine should leak in the front at all. If so, then it's time to replace the bearings. Bad front bearing can cause the engine to lean and have a bad idle. The inside bearing can stop the engine...
    Liked On: 10-10-2022, 10:36 AM
    Posted On: 08-09-2022, 09:49 AM
  13. Rcdad42 liked post by 1995 Monster T On thread : Is reusing off road wheels common?
    Yes you can. Just don't use that much glue next time. Try deborder next time to remove the glue. If the wheels are nylon, it's ok,
    Liked On: 08-28-2022, 11:47 AM
    Posted On: 08-25-2022, 05:46 AM
  14. AHR43
    AHR43 liked post by 1995 Monster T On thread : Drill press recommendations for hobbies
    A drill press with 3-5 speeds. A 8" table bench top model and 1/2" shank capacity chuck.
    Liked On: 08-20-2022, 09:18 AM
    Posted On: 08-17-2022, 11:40 AM
  15. Jaredf liked post by 1995 Monster T On thread : Flywheel keeps coming loose
    Yes! blue locktite willl work. if it loosens up use red. Metal to metal requires Loctite blue.
    Liked On: 08-19-2022, 12:27 PM
    Posted On: 08-19-2022, 12:15 PM
Page 3 of 4
1
2
3
4

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.