Xray T4'14
#676
Tech Elite
iTrader: (2)
Newest T4'14 Owner
Brenden Newbury (9) won himself a brand new XRay T4'14, courtesy of Ralph Burch of RC America, with a wire to wire Scale Spec B-Main finish at last weekends Timezone Gran Prix Ralph waited until the field was gridded up and then made the announcement, the winner would be getting a new T4'14. You could tell by the looks of the drivers faces that the pressure was on! Brenden isn't one that likes pressure, but with 40+ spectators and the always entertaining Charlie Suangka on the mic, you would have thought the kid was going for the World title! Brenden stayed calm, cool, and collected to run a nearly flawless race with his T3'12. He was so calm that he called out with 45 seconds left "I got this!" After the final tone went off and he finished his final lap with all the fan fare going on, I got to have one of the great father-son moments. He will be building the car himself with my assistance and it will be all his, He earned it
Ryan
Ryan
#677
TEAR *( so touching T-bag so touching.LOL ... But good JOB for him I was cheering for him on LiveRC!
Last edited by Mr.A Morris; 11-19-2013 at 07:27 AM.
#679
Tech Rookie
Hi,
I am racing 13.5t stok class( No boost ) in med-high traction carpet track & I would like to know what can I do for make my care faster !??!
I mean decreasing rear toe, less camber ... Etc ?!?
Thanks
I am racing 13.5t stok class( No boost ) in med-high traction carpet track & I would like to know what can I do for make my care faster !??!
I mean decreasing rear toe, less camber ... Etc ?!?
Thanks
#680
Tech Regular
#681
#682
T4 14
Well I just got mine built and ran it...and it was dialed..I couldn't be happier
The car was on rails and cornering was great
The car was on rails and cornering was great
#683
Tech Regular
#684
Hey guys,
Been out of the 1/10 scene for a while but a new local race series has really piqued my interest so I got a new addition to the family.
We're running the orca 11.5t motor and I'm limited to an FDR of 6.6 due to limited gear options at the moment. Is this too low for open mod settings?
Am going with the Muchmore Fleta 4 esc. Any suggestions on settings?
This is the track we run on.
http://www.youtube.com/watch?v=azZO2t9QuC0
Thanks for any info provided
Been out of the 1/10 scene for a while but a new local race series has really piqued my interest so I got a new addition to the family.
We're running the orca 11.5t motor and I'm limited to an FDR of 6.6 due to limited gear options at the moment. Is this too low for open mod settings?
Am going with the Muchmore Fleta 4 esc. Any suggestions on settings?
This is the track we run on.
http://www.youtube.com/watch?v=azZO2t9QuC0
Thanks for any info provided
#685
Tech Adept
Track width!!
Hi,
Could someone explain the main effects from widening and narrowing the front and rear track width?
thanks!!
Could someone explain the main effects from widening and narrowing the front and rear track width?
thanks!!
#687
I've stripped all my hexes
#688
Tech Master
iTrader: (4)
I also had an issue with my hexes - in short, check your screws. I found that one screw was slightly smaller than the other screws and wouldn't even thread - I also had another one which 'stripped' out. I ended up replacing the hex screws with those from another car I had. No issues since, even with the hex that had originally stripped.
#690
Tech Regular
Widening at the pivot pins adds stability
HTH's
HTH's