Tamiya TA05 Touring Sedan
#7022
Originally Posted by nexxus
I ran 1A's all round with standard suspension, and 1A's front, 1A / 1D rear when running lightweight suspension.
#7023
Tech Master
iTrader: (1)
B3's !
SuperEK4,
I would put the front sway bar back on then go to a softer angle on shock position in the rear, then a softer spring in the rear,then increase negative camber in the rear, then increase negative toe in the rear, then increase the droop in the front. Try and use soft or medium soft inserts on B3's!
Of coarse do each of these changes one at a time and then drive a few laps and see if you like. Need more rear grip then go to the next change, so on and so forth! Last, Tamiya "B3"tires aren't the best tires out there. They only last a few runs and they are sooooo! done!
Trust me, you won't be disappointed!
I would put the front sway bar back on then go to a softer angle on shock position in the rear, then a softer spring in the rear,then increase negative camber in the rear, then increase negative toe in the rear, then increase the droop in the front. Try and use soft or medium soft inserts on B3's!
Of coarse do each of these changes one at a time and then drive a few laps and see if you like. Need more rear grip then go to the next change, so on and so forth! Last, Tamiya "B3"tires aren't the best tires out there. They only last a few runs and they are sooooo! done!
Trust me, you won't be disappointed!
#7024
Tech Lord
iTrader: (32)
hi, i have a m sonik 8t esc. but I have to run my tx on reverse to have the car running forward.the motor n batt wires on the esc is correct. Only thing is I have to reverse my tx to run it. Will it harm my esc?
My esc also shuts down after 5mins of race becoz of overheat? can i reverse my wires on my motor to ran normal on my tx? will it be better. I m running on 23t stock RZ on Ta05r with 5:9 ratio.
By theory it should not overheat. the belt & meshing is ok too? Any experts can tell me y?
My esc also shuts down after 5mins of race becoz of overheat? can i reverse my wires on my motor to ran normal on my tx? will it be better. I m running on 23t stock RZ on Ta05r with 5:9 ratio.
By theory it should not overheat. the belt & meshing is ok too? Any experts can tell me y?
#7025
Tech Lord
iTrader: (32)
Originally Posted by maxepower
SuperEK4,
I would put the front sway bar back on then go to a softer angle on shock position in the rear, then a softer spring in the rear,then increase negative camber in the rear, then increase negative toe in the rear, then increase the droop in the front. Try and use soft or medium soft inserts on B3's!
Of coarse do each of these changes one at a time and then drive a few laps and see if you like. Need more rear grip then go to the next change, so on and so forth! Last, Tamiya "B3"tires aren't the best tires out there. They only last a few runs and they are sooooo! done!
Trust me, you won't be disappointed!
I would put the front sway bar back on then go to a softer angle on shock position in the rear, then a softer spring in the rear,then increase negative camber in the rear, then increase negative toe in the rear, then increase the droop in the front. Try and use soft or medium soft inserts on B3's!
Of coarse do each of these changes one at a time and then drive a few laps and see if you like. Need more rear grip then go to the next change, so on and so forth! Last, Tamiya "B3"tires aren't the best tires out there. They only last a few runs and they are sooooo! done!
Trust me, you won't be disappointed!
#7026
Tech Master
iTrader: (1)
Originally Posted by SuperEk4
hi, i have a m sonik 8t esc. but I have to run my tx on reverse to have the car running forward.the motor n batt wires on the esc is correct. Only thing is I have to reverse my tx to run it. Will it harm my esc?
My esc also shuts down after 5mins of race becoz of overheat? can i reverse my wires on my motor to ran normal on my tx? will it be better. I m running on 23t stock RZ on Ta05r with 5:9 ratio.
By theory it should not overheat. the belt & meshing is ok too? Any experts can tell me y?
My esc also shuts down after 5mins of race becoz of overheat? can i reverse my wires on my motor to ran normal on my tx? will it be better. I m running on 23t stock RZ on Ta05r with 5:9 ratio.
By theory it should not overheat. the belt & meshing is ok too? Any experts can tell me y?
Just my 2$
#7030
Tech Lord
iTrader: (32)
Originally Posted by nexxus
An RZ I'd gear at 7.2, so in that case, 5.9 is even worse!
Try that gearing, (I believe with a 105 spur a 30 or 31 pinion will do it, if you run the standard 70 tooth spur, you ideally want a 21 or 22 pinion) and may find the ESC behaves better as well!
Try that gearing, (I believe with a 105 spur a 30 or 31 pinion will do it, if you run the standard 70 tooth spur, you ideally want a 21 or 22 pinion) and may find the ESC behaves better as well!
#7031
Tech Master
iTrader: (53)
Originally Posted by SuperEk4
i gear at 5.9 is that y my esc overheats?
#7032
R/C Tech Elite Member
iTrader: (315)
I guess it's track / climate dependant
If you try and run a TZ or an RZ at a ratio like 6 or 6.5 at our local track, you best bring a fire extinguisher and be ready in 1-2 minutes. Even Sports tuneds geared at that rate are lasting maybe 2-3 runs then game over.
If you try and run a TZ or an RZ at a ratio like 6 or 6.5 at our local track, you best bring a fire extinguisher and be ready in 1-2 minutes. Even Sports tuneds geared at that rate are lasting maybe 2-3 runs then game over.
#7033
Tech Master
iTrader: (5)
Just wanted to take a minute and thank everyone for their assistance and advise.... I've been reading this thread since it started and was personally convinced to purchase a TA05 and have been impressed with this vehicle since receiving it. I will be giving it through shake down Saturday at Primetime Raceway, preparing it for battle at the TCS GT2 war in Memphis , hope to meet some fellow forum members there!
Last edited by rctouringracer; 04-12-2007 at 11:51 PM.
#7034
Tech Master
iTrader: (53)
Originally Posted by nexxus
I guess it's track / climate dependant
If you try and run a TZ or an RZ at a ratio like 6 or 6.5 at our local track, you best bring a fire extinguisher and be ready in 1-2 minutes. Even Sports tuneds geared at that rate are lasting maybe 2-3 runs then game over.
If you try and run a TZ or an RZ at a ratio like 6 or 6.5 at our local track, you best bring a fire extinguisher and be ready in 1-2 minutes. Even Sports tuneds geared at that rate are lasting maybe 2-3 runs then game over.
i ever tried gearing the TZ at 5.2, it stopped dead at around the 3 minute mark in a 5 min race, got a red comm and unsoldered motor wires...but it was plenty fast though.
#7035
To be blunt the MTroniks MSonik range of speedos are pretty pathetic, it saddens me to say it because they are a British product.
Try switching to something more reputable, I think a lot of your problems will stop there.
Try switching to something more reputable, I think a lot of your problems will stop there.