Hot Bodies Cyclone
#3076
would the hot bodies 44mm steel bone fit the tamiya trf415 driveshaft axles?
#3078
Tech Master
iTrader: (6)
Originally Posted by nordheim
Hi guys!
I sold my Cyclone but had a couple of things on order before I did so. Anyone interested in the following new in package:
1 31t 64p Robinson Racing superlite pinion gear $4.00 shipped
1 32t 64p Robinson Racing superlite pinion gear $4.00 shipped
1 106t 64p Hpi Purple Spur gear $3.00 shipped
All 3 for $10.00 shipped. PM me if interested.
I sold my Cyclone but had a couple of things on order before I did so. Anyone interested in the following new in package:
1 31t 64p Robinson Racing superlite pinion gear $4.00 shipped
1 32t 64p Robinson Racing superlite pinion gear $4.00 shipped
1 106t 64p Hpi Purple Spur gear $3.00 shipped
All 3 for $10.00 shipped. PM me if interested.
#3079
What springs do you guys use for carpet/foam ? Hara's set-up sheet from Vegas says 33# front and 28# rear. Does HPI make these springs and if so does anybody know the part numbers ?
Thanks.
Thanks.
#3080
Pretty sure those are Xray Springs that he was using. Check it out:http://www.teamxray.com/teamxray/pro...477&kategoria=
#3081
Corally silver spring set. Comes in a package of 6 pairs, 26-44lbs for less than $20. They are the same size as HPI springs too.
#3083
Thanks !
Any word on the BMI Cyclone carpet chassis ?
Any word on the BMI Cyclone carpet chassis ?
#3084
I keep being told to use some titanium ball studs as the standard ones break easily. What is everyone using?
Thanks
Thanks
#3086
Originally Posted by XrayFK
Square makes titanium ball studs.
Just tried speedtech but they are out is there anyone else who might stock them or another manufacturer?
Thanks
#3087
Tech Champion
iTrader: (9)
Originally Posted by tim fry
Just tried speedtech but they are out is there anyone else who might stock them or another manufacturer?
Thanks
Thanks
try Allspeed Hobbies they might have some left...see sig for link
or try RainbowTen in Japan, Rcmodel or Precision RC in HK.
#3088
Thought I would share my carpet setup with you guys, you'll find that it's not too far away from the stock setup...
EDIT: Droop is measured above ride height.
EDIT: Droop is measured above ride height.
#3089
Tech Adept
Anyone ever get a bent motor mount in their kit?
First time I went to race the car, meshed up the gears and switched it on in the pits and held up in the air and gave it a few revs... there was a terrible clicking sound coming from the car. Seemed like it wasn't meshed properly so I re-checked it and it was fine, but still this clicking noise. Changed to 48p gears and problem went away. When racing last night it was alright, until I noticed the motor wasn't sitting straight in the car so I unscrewed it and tried to reset the motor... still crooked.... then unscrewed the motor mount thinking it was just tweaked but it wasn't. The only thing left was that it was bent, and not just a little either. Do you think it may have been bent a little from factory which caused that clicking sound initially and after having driven the car made it worse? By the way I never had any impacts on the motor (not a scratch on it) or anything that might cause a bent motor mount, plus i've never had this problem with any other car.
First time I went to race the car, meshed up the gears and switched it on in the pits and held up in the air and gave it a few revs... there was a terrible clicking sound coming from the car. Seemed like it wasn't meshed properly so I re-checked it and it was fine, but still this clicking noise. Changed to 48p gears and problem went away. When racing last night it was alright, until I noticed the motor wasn't sitting straight in the car so I unscrewed it and tried to reset the motor... still crooked.... then unscrewed the motor mount thinking it was just tweaked but it wasn't. The only thing left was that it was bent, and not just a little either. Do you think it may have been bent a little from factory which caused that clicking sound initially and after having driven the car made it worse? By the way I never had any impacts on the motor (not a scratch on it) or anything that might cause a bent motor mount, plus i've never had this problem with any other car.
#3090
Hot Bodies t-shirts
Hot Bodies t-shirts
Anyone know where to get the black t-shirts that I've seen Hara, Surikarn, Moore and the other team drivers wearing?
Thanks!
Anyone know where to get the black t-shirts that I've seen Hara, Surikarn, Moore and the other team drivers wearing?
Thanks!