Hot Bodies TCX
#4427
Here ya' go bud. BTW, hope to see you soon @ T&L! I need some onroad fix soon!
http://www.jethobby.com/_Jet%20Racin...X%20Parts.html
http://www.jethobby.com/_Jet%20Racin...X%20Parts.html
#4428
Tech Elite
iTrader: (102)
Join Date: Dec 2004
Location: Far away from Covid19 but close to 20
Posts: 4,129
Trader Rating: 102 (100%+)
Here ya' go bud. BTW, hope to see you soon @ T&L! I need some onroad fix soon!
http://www.jethobby.com/_Jet%20Racin...X%20Parts.html
http://www.jethobby.com/_Jet%20Racin...X%20Parts.html
Track is ready.
Sat 12noon is the usual start time.
Now to decide to buy them all. or just 0 and .5 split block
#4429
Tech Champion
iTrader: (30)
I had them on my USVTA car at the Slowbirds - and I think i did pretty well with it in VTA
just wish i could find a cheap TCX to have for normal TC racing
#4431
Tech Elite
iTrader: (102)
Join Date: Dec 2004
Location: Far away from Covid19 but close to 20
Posts: 4,129
Trader Rating: 102 (100%+)
#4433
Tech Apprentice
ok, dumb question time. What is the degree of the standard HB FR block then (given the degree amounts for the Jet Racing split blocks) ?
here in the UK right now im running a 2.0FF block, and a 2.0FF (but modified to fit in the FR location). This put the wishbones dead level to the bulkheads.
Any idea what blocks I should order to get the same, but using the JR split blocks ?
Cheers
here in the UK right now im running a 2.0FF block, and a 2.0FF (but modified to fit in the FR location). This put the wishbones dead level to the bulkheads.
Any idea what blocks I should order to get the same, but using the JR split blocks ?
Cheers
#4434
Tech Master
iTrader: (14)
MINT condition Hot Bodies TCX with tons of spares including a second set of shocks, spare arms, knuckles... etc. Only ran on carpet with a 17.5 blinky 3 races. It has many hop-up parts including aluminum knuckles (tamiya 417 for better geometry), aluminum rear hubs (also tamiya 417).
Roller only (with parts) $300 + shipping
Almost Ready to Run (with a Speed Passion LPF Speed control and a 21.5 trinity motor) set-up for blinky 21.5 $450 + shipping
Roller only (with parts) $300 + shipping
Almost Ready to Run (with a Speed Passion LPF Speed control and a 21.5 trinity motor) set-up for blinky 21.5 $450 + shipping
#4436
i run my tcx pretty standard except 3 hole 1.1 pistons 3 hole hubs(using extra hole) and tcx lower shock towers. I am trying to get more low speed steering on my car, i always seem to end up running 2 deg rear toe-in at the end of the day otherwise the car is just not fast enough and pushes wide.
my setup for 13.5 open
FRONT
pink front springs
45wt shock oil
camber 1.5deg
0 deg toe
droop 5 measured using associated plastic droop gauge
1.5 FF pivot block
1.5mm spacers FF RR
shock position no 2 from inside
Rear
silver rear springs
40wt shock oil
camber 1.5deg
2 deg rear toe-in
droop 4 measured using associated plasic droop gauge
1.5mm spacers
shock position no 4 from inside
ball diff
sorex 32's
usually racing on medium grip asphalt tracks in UK
my setup for 13.5 open
FRONT
pink front springs
45wt shock oil
camber 1.5deg
0 deg toe
droop 5 measured using associated plastic droop gauge
1.5 FF pivot block
1.5mm spacers FF RR
shock position no 2 from inside
Rear
silver rear springs
40wt shock oil
camber 1.5deg
2 deg rear toe-in
droop 4 measured using associated plasic droop gauge
1.5mm spacers
shock position no 4 from inside
ball diff
sorex 32's
usually racing on medium grip asphalt tracks in UK
#4437
i run my tcx pretty standard except 3 hole 1.1 pistons 3 hole hubs(using extra hole) and tcx lower shock towers. I am trying to get more low speed steering on my car, i always seem to end up running 2 deg rear toe-in at the end of the day otherwise the car is just not fast enough and pushes wide.
my setup for 13.5 open
FRONT
pink front springs
45wt shock oil
camber 1.5deg
0 deg toe
droop 5 measured using associated plastic droop gauge
1.5 FF pivot block
1.5mm spacers FF RR
shock position no 2 from inside
Rear
silver rear springs
40wt shock oil
camber 1.5deg
2 deg rear toe-in
droop 4 measured using associated plasic droop gauge
1.5mm spacers
shock position no 4 from inside
ball diff
sorex 32's
usually racing on medium grip asphalt tracks in UK
my setup for 13.5 open
FRONT
pink front springs
45wt shock oil
camber 1.5deg
0 deg toe
droop 5 measured using associated plastic droop gauge
1.5 FF pivot block
1.5mm spacers FF RR
shock position no 2 from inside
Rear
silver rear springs
40wt shock oil
camber 1.5deg
2 deg rear toe-in
droop 4 measured using associated plasic droop gauge
1.5mm spacers
shock position no 4 from inside
ball diff
sorex 32's
usually racing on medium grip asphalt tracks in UK
#4438
roll centres are 1.5mm all round
i use fastrax shock oil i don't know how that compares to your much more oil. I race on most tracks in the UK the only place i have had the car how i like it was at stafford's BRCA Clubmans. I guess the setup is mostly for Bedworth as this is my local track
#4439
#4440
Tech Apprentice
i run my tcx pretty standard except 3 hole 1.1 pistons 3 hole hubs(using extra hole) and tcx lower shock towers. I am trying to get more low speed steering on my car, i always seem to end up running 2 deg rear toe-in at the end of the day otherwise the car is just not fast enough and pushes wide.
my setup for 13.5 open
FRONT
pink front springs - try silver
45wt shock oil - perhaps try 40wt but id go no lower
camber 1.5deg - shuold be ok, but how is the tyre wearing ? across the face or just the inside half, if only inside half go to 2deg
0 deg toe - 0.5 toe out either side (1mm total overall)
droop 5 measured using associated plastic droop gauge
1.5 FF pivot block I normally run 2.0ff & Fr)
1.5mm spacers FF RR
shock position no 2 from inside - try 3 or even 4, seems wierd but actually induces more turn in due to pressure on the arm)
Rear
silver rear springs
40wt shock oil
camber 1.5deg - try 2.0deg
2 deg rear toe-in - try 2.5 or even 3
droop 4 measured using associated plasic droop gauge
1.5mm spacers (make the car just short of long wheelbase (put the small spacer behind the wishbone at the pivot block and the same on the rear hub)
shock position no 4 from inside
ball diff - Do you have a GearDiff at all ? If so build this with 55wt schumacher oil or a loose GD oil
sorex 32's - what trye prep and additive ?
usually racing on medium grip asphalt tracks in UK
my setup for 13.5 open
FRONT
pink front springs - try silver
45wt shock oil - perhaps try 40wt but id go no lower
camber 1.5deg - shuold be ok, but how is the tyre wearing ? across the face or just the inside half, if only inside half go to 2deg
0 deg toe - 0.5 toe out either side (1mm total overall)
droop 5 measured using associated plastic droop gauge
1.5 FF pivot block I normally run 2.0ff & Fr)
1.5mm spacers FF RR
shock position no 2 from inside - try 3 or even 4, seems wierd but actually induces more turn in due to pressure on the arm)
Rear
silver rear springs
40wt shock oil
camber 1.5deg - try 2.0deg
2 deg rear toe-in - try 2.5 or even 3
droop 4 measured using associated plasic droop gauge
1.5mm spacers (make the car just short of long wheelbase (put the small spacer behind the wishbone at the pivot block and the same on the rear hub)
shock position no 4 from inside
ball diff - Do you have a GearDiff at all ? If so build this with 55wt schumacher oil or a loose GD oil
sorex 32's - what trye prep and additive ?
usually racing on medium grip asphalt tracks in UK