R/C Tech Forums - The Speed Passion Thread

The green board is next 21* to 30*. Then yellow 31* to 40*. Then blue 41* to 50*.
I personally like the green board so far for 17.5 blinky. I keep switching back and forth between the green and the yellow. Make sure you drop a couple teeth when switching boards and watch temps.

Alright, just so I am clear on this. The +10, +20, +30, etc All refer to the base timing? Meaning the stock red sensor board bumps the base timing up by 10 to start with and goes to 20?

M-Technic

08-17-2012 12:37 PM

Quote:

Originally Posted by puhrot (Post 11104959)

Alright, just so I am clear on this. The +10, +20, +30, etc All refer to the base timing? Meaning the stock red sensor board bumps the base timing up by 10 to start with and goes to 20?

There is base timing "built into" the motor that is always there no matter which timing ring you are using.

The stock board goes from +11-20*. The green board goes from +21-30*. The yellow board goes from +31-40*. And the blue goes from +41-50*. These are on top of the "built in" timing.

If you want to add 10* on top of the stock board, you should go with the green board.

gdcopbdcop

08-18-2012 11:50 AM

guys, i am at the track now, running a 2.0 pro. we are racing 17.5 boosted. i am using the set up posted in the S/P web site. I need the boost to come in just a bit sooner. What can i do or change to start the boost just a bit sooner?

Thanks,
rich

shmit 1

08-18-2012 08:58 PM

Quote:

Originally Posted by Solara (Post 11096119)

Please try to turn off the THERMAL protection via the programmer card.

That fixed my problems, thanks for the help.:)
It also helped 2 other racers at the track today.

miz4	08-18-2012 11:38 PM

I'm having the same issue with the Reventon S that i just got. Should I do the same thing and turn off the thermal protection?

Mxer59

08-19-2012 09:10 PM

I'm getting back into rc and would like some info, will any of the new Revention series Esc be able to handle a 4-pole 4x4 sct setup

Marcos.J

08-20-2012 06:11 AM

Ran the reventon r yesterday , very nice! Very smooth, little soft on the brakes but I will figure it out :)

M-Technic

08-20-2012 06:23 AM

Quote:

Originally Posted by miz4 (Post 11109688)

I'm having the same issue with the Reventon S that i just got. Should I do the same thing and turn off the thermal protection?

You shouldn't run with the thermal protection on for any racing applications.

Solara

08-20-2012 09:34 AM

Quote:

Originally Posted by gdcopbdcop (Post 11108073)

Item 13 and 15...the lower the number, the faster and harder it will hit, also, temps go higher and sooner too.

Solara

08-20-2012 09:38 AM

Quote:

Originally Posted by shmit 1 (Post 11109374)

That fixed my problems, thanks for the help.:)
It also helped 2 other racers at the track today.

Glad that work............for your information, I don't use LIPO cuttoff as well. I pull off after 6 minutes no matter I am practicing or racing, I never overrun my lipo/car....turning that off will avoid the DNF while racing.

Solara

08-20-2012 09:39 AM

Quote:

Originally Posted by Mxer59 (Post 11112753)

I'm getting back into rc and would like some info, will any of the new Revention series Esc be able to handle a 4-pole 4x4 sct setup

NOT YET....only the REVENTON PRO can run the 4 pole 4x4 motor with boost. Should be out like October time.

Solara

08-20-2012 09:41 AM

A little preview....debut this week at the ON ROAR PAVED NATIONAL 2012

http://www.kinggolden-rc.com/product.../sp000222a.jpg

http://www.kinggolden-rc.com/product.../sp000162a.jpg

Solara

08-20-2012 09:41 AM

Quote: