|
Originally Posted by Snafujg
(Post 11913009)
I'm looking to get a Reventon Stock Club ESC to run blinky 17.5 in my 2wd SC10. I have a Savox 1258 in the truck. Anyone experience brown out issues with this combo? I know the Savox are power hungry. Just want to make sure the ESC BEC is up to the task of a Savox servo before I buy one.
Great ESC too, comes ready out of the box, wires on, Dean's connector on, fan mounted, ready to rock. |
Originally Posted by quickershifter
(Post 11915527)
I can't get my Rev R to on the turbo/boost. How to set it up? I'm running Yeah Racing Hackmoto 13.5T BL motor.
|
Reventon Pro Setup Setting
Any good settings for 17.5 Blinky? Wanted to see if anyone has a good starting setup.
Thx. |
Hey guys, need help with a starting setup and FDR for a Reventon Pro in 21.5T boosted. Going to try this class again, last time I blew two motors trying to get a fast setup so don't want to repeat that mistake :)
Thanks |
Originally Posted by DJGonzo69
(Post 11917375)
Any good settings for 17.5 Blinky? Wanted to see if anyone has a good starting setup.
Thx. 2-3 3-8 4-8 5-1 6-3 7-1 Start at 4.0 FDR and 30-ish degrees of timing and add teeth and timing as necessary. |
Reventon Pro Setup with Yeah Racing 21.5t Open Setup
Hi Guys
Looking for a setup for the above. Track is Low Traction Mixed Track with 65metre main straight Also will need FDR to run with aswell Thanks |
I have programmed my Reventon R to do forward/reverse. However I have a problem with it: It won't always do reverse. I pull back many times on the transmitter but nothing happens. It seems to do reverse sometimes but not always.
The strange thing is that the brake function always works fine, so there is nothing wrong with the signal... |
Originally Posted by Andy w
(Post 11911801)
As I said in my post, mine DOES work with a 1s. It works with either a rx pack or booster. I am trying to figure out why when it supposedly shouldn't.
When was your REVENTON S or R purchased..? I want to know too... |
Originally Posted by akisole
(Post 11912168)
Every time i load a new software i recalibrate the speed.The timing in x20 is the lowest 4dot 27.5 the other is 30, 32.5, 35 and 37.5.
I will tell you exacly what it made me. For the first 30 seconds the speed work in full throttle.after that when i keep the trhottle in 1/4 for 1 sec(entering a corner) and give all the thortle exiting the corner the car goes with 1/4 of thorthe.I dont have full thortle.When i leave and give again full thortle gives me 3/4.I work it like a nitro with playing all the time with trhottle to work. I play Drag Brake Force 15% Low Voltage Cut-Off 3,4v/cell "DDRS" Start Mode level 3 Maximum Reverse Force 50% Initial Brake Force 0% Neutral Range 6%(Narrow) Turbo Open Time 12 deg/0.1sec Boost Start RPM 9000rpm Turbo Open Delay 0.2 sec acc 750 It is sensor problem....either your sensor cable, or the sensor board inside the motor is bad....the last thing, the sensor port of the ESC is bad. Check all 3 items... |
Originally Posted by EDWARD2003
(Post 11915052)
Okay.... were in Japan can I purchase the greening timing board for MMM motors?
http://www.tresrey.com/ |
Originally Posted by Solara
(Post 11926931)
May I know what booster you use..? I would LOVE to know that...cause I have this question asked so many times and I have no solution, until now...
When was your REVENTON S or R purchased..? I want to know too... It is a R and used a old Novak Smartboost that I got 2nd hand. I also used a LiFe rx pack with it and it worked. It was paired with a Reedy Sonic 13.5. Everything worked as any 1s has worked for me in the past. I bought it from the SP website on Oct. 12. At the time I used the firmware that it came with and have since loaded the stock0 firmware for my TC. I know I didn't dream this and the only reason I switched the esc is I had a LRP SXX laying around and it made my chassis cleaner without all the extra wires and battery. When I can I will switch it back and see if it still works with the new firmware. |
Originally Posted by coretex
(Post 11926746)
I have programmed my Reventon R to do forward/reverse. However I have a problem with it: It won't always do reverse. I pull back many times on the transmitter but nothing happens. It seems to do reverse sometimes but not always.
The strange thing is that the brake function always works fine, so there is nothing wrong with the signal... |
Originally Posted by Andy w
(Post 11927855)
It is a R and used a old Novak Smartboost that I got 2nd hand. I also used a LiFe rx pack with it and it worked. It was paired with a Reedy Sonic 13.5. Everything worked as any 1s has worked for me in the past.
I bought it from the SP website on Oct. 12. At the time I used the firmware that it came with and have since loaded the stock0 firmware for my TC. I know I didn't dream this and the only reason I switched the esc is I had a LRP SXX laying around and it made my chassis cleaner without all the extra wires and battery. When I can I will switch it back and see if it still works with the new firmware. |
Finally got the Reventon S going in my buggy last night and the Wifi module working today. Very smooth control and the Wifi module is the cats a$$! I see that there isn't a 'hybrid boost' setting with the S model. Are there any future plans to incorporate this setting into the S model?
|
when new software will be released?
Stock0 has serious cogging at low throttle |
| All times are GMT -7. It is currently 09:13 PM. |
Powered By: vBulletin v3.9.3.9 Patch Level 3
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.