|
"Unfortunately, there is a Bug in FW 100422 DDRS, can be solved?"
Originally Posted by charlie_b
(Post 7404415)
DDRS we leave it at 8 or 9. Reason being, with the Supercharger software, we now control punch with SC Punch #15. If you want more punch, lower your parameter on #15. All these settings relate to each other. If you turn down DDRS too low, SC Punch will not be activated.
|
Help
Need some help,I downloaded the new software and have it installed on my speedie but my LCD progammer still has the 225 software on it so I can not use the LCD programmer to change my settings, it works via the pc though. Any suggestions are welcome.
When I try to use the lcd programmer it comes up with a please update software message. |
The new supercharger firmware will not work with the lcd programmer. Use the original program card that came with the esc. All 15 settings will then be made available with it.
|
I thought you update the programmer to 1.05 and it does?
|
Originally Posted by Abu Salahuddin
(Post 7431936)
The new supercharger firmware will not work with the lcd programmer. Use the original program card that came with the esc. All 15 settings will then be made available with it.
Included is the 100422_STOCK, the 09205_MOD, and the 100508ZERO. |
Originally Posted by AGNO
(Post 7430942)
"Unfortunately, there is a Bug in FW 100422 DDRS, can be solved?"
The bug has been fixed. |
HELP
Thanks,
The old standard box which comes with the speedie works so I can now change settings with out my pc,is there a way to make the newer 2in 1 box work as well. |
Originally Posted by xrayal
(Post 7433121)
on the OTHER THREAD, a new 518software has been released, apparently sorting out the BUG. is SP going to update or bring out something similar to erradicate the bug also?
|
:nod::nod:
|
Originally Posted by stinky cheese
(Post 7433377)
Thanks,
The old standard box which comes with the speedie works so I can now change settings with out my pc,is there a way to make the newer 2in 1 box work as well. When you plug in the lcd box if you click on device a drop down box will show ESC speedcontroller Motor Function Checker LCD program unit Click on LCD program unit and it should say somewhere there about update click on that and all should be well. Run the upgrade a few times to make sure all goes in. Otherwise ask Sandy at your work he knows what to do. |
Originally Posted by stinky cheese
(Post 7433377)
Thanks,
The old standard box which comes with the speedie works so I can now change settings with out my pc,is there a way to make the newer 2in 1 box work as well. |
Is there an updated USER GUIDE/SETUP GUIDE out for this new software? Something that would tell us that DDRS should be at 8 or 9?
I ran it last nite in my buggy and it was pretty good but i could have used a bit more bottom end, i was using DDRS at 7. |
HELP
Thanks to those for their input, I managed to update my older 2in1 programmer but the newer one with the software ending in 255 will not let me update to the 420 software. Cheese
|
Originally Posted by Joel Lagace
(Post 7433959)
Is there an updated USER GUIDE/SETUP GUIDE out for this new software? Something that would tell us that DDRS should be at 8 or 9?
I ran it last nite in my buggy and it was pretty good but i could have used a bit more bottom end, i was using DDRS at 7. |
Originally Posted by charlie_b
(Post 7433533)
I am not even aware of any "BUG" when using the Supercharger software, we leave DDRS at 8 or 9. In fact, even when we did not have the supercharger software, we never went below 8. Anything below 8 is Useless...
|
| All times are GMT -7. It is currently 07:35 PM. |
Powered By: vBulletin v3.9.3.9 Patch Level 3
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.