DaveW

iTrader: (1)

I would also like a 3mm thick LiPo chassis. Reducing width isnt as important to me, as i am not fond of my electronics being so vulnerable as it is.

I actually wish someone would incorporate some LW molded composite side guards on a TC... kinda like what you would find on an offroad nitro car. Something cheap and easy to replace.... unlike my motor, sensor wire, or speedo.

hanzo3

iTrader: (55)

I am contemplating if u should buy another lipo edition chassis. I am running 6cell rubber. I need new outdrives and the thinner top deck for bullet connectors.

jlfx car audio

iTrader: (37)

i just had a weekend worth of awesome racin in nashville tn.
ran my photons in vta(21.5 version) and 17.5 spec.
i had some good runs early on (4heats)
my 1st round runs in both classes held my up near the front of tc behind robert dirla and eric anderson and one more ( he got his car workin a touch better in his 4th run. i had some sweeper issues and let me tell ya i had some HARD hits around the sweeper and in 5 rounds of racin my car hit and bashed its way thru that sweeper probably 10 times. ( narrow sweet spot entering sweeper, strait is a bit bumpy) but not wonce did i have to turn one wrench!
tweek/ droop( small adj) / height/ repair/ gearing perfect all weekend.
ended up in the back of the a main ( lost my 1oz wait in front bumper and it made it bad loose.
in vta i set tq in first round and it held till round 4 when i was out done by 1 sec! same issues sweeper sweety spot got me , but not in the main. i had it by far had the better car setup. it was BUTTER. had 1 bed sweeper tumble
10' of the track late in main and lost my big lead. still won but only by 1.7sec!
awesome cars

devilsquid

iTrader: (2)

Well Stilskin didnt post it but he got second in our A main this last weekend and Photons took 1,2,3 in our B main. It was good racing and with alittle more time, I should be up there in the Amain rubbing venders with the big boys.

rcfiend

iTrader: (42)

I'm getting back into the hobby and I have placed an order for the TOP car. Can't wait to get my hands on it. I have a question for those of you using the M11x; how much space does the airtronics receiver take up. I'm trying to decided between the M11x and the KO Euros radio.

devilsquid

iTrader: (2)

I have the M11, not sure what the size difference between it and the x are but here is what mine looks like with the 11,bls 351,tekin rs.

rcfiend

iTrader: (42)

Thx. devilsquid. What receiver are you using with your M11? Are you using the M11X or M11?

devilsquid

iTrader: (2)

Its the one that came with my M11 when I bought it from Amain this last summer. 2.4 ghz but I have the module plugged into the side of my TX,where as I don't believe you have to with the 11x.

rcfiend

iTrader: (42)

Ok. Thx for the input.

hanzo3

iTrader: (55)

Does the soft rubber narrow top deck come with new screws? If I am buy a new top and main chassis, might as well feta née lipo spec kit then?

OVA

iTrader: (86)

Nope.... I don't think the screws are included with the top deck....

locked

iTrader: (1)

I was going to replace the chassis, shocks, a few other bits and get a new ball diff for my old v1 photon, but I decided to just get a whole new kit, because it wasn't much more than buying those few parts separately and that way I have a second full car. I don't think the new screws are included if you just buy a new top deck as a standalone part. You would need to pick up 2 packs of the new screws to replace all of them.

rcfiend

iTrader: (42)

What is the link to order a car directly from Top?

hanzo3

iTrader: (55)

Just email them. Their online store got hacked.

odpurple

[email protected] 650-583-8898

Friendly service, same day shipping