Veteran TAMIYA TA03 fans!
#1441
TMYJOY TA03F
Well I don't own a rc car y believe since I was 21 now 31 a quick look to ebay change all that I found a TA03F RTR was a Audi A4STW of course bath tub chassis . I charge the battery and tested too slow. Last rc car that I drive was a Tamiya M03 mini cooper but is the mini was slow The TA03f is worse . Ok time to take a look to the internet and read about it and I find this forum. First thing I want to replace was the bath tub chassis for that sexy looking FRP chassis hard to find but my Friend IROCKFLIFLOPS don't hesitate to sell my a new spare of the lower chassis later on I find a new top part from ebay and a couple more hop ups.....
#1442
Tech Addict
iTrader: (33)
Well I don't own a rc car y believe since I was 21 now 31 a quick look to ebay change all that I found a TA03F RTR was a Audi A4STW of course bath tub chassis . I charge the battery and tested too slow. Last rc car that I drive was a Tamiya M03 mini cooper but is the mini was slow The TA03f is worse . Ok time to take a look to the internet and read about it and I find this forum. First thing I want to replace was the bath tub chassis for that sexy looking FRP chassis hard to find but my Friend IROCKFLIFLOPS don't hesitate to sell my a new spare of the lower chassis later on I find a new top part from ebay and a couple more hop ups.....
#1443
no its looking to ugly right now....
#1444
Tech Rookie
oh man
Last edited by gewizz2; 05-13-2018 at 03:04 AM.
#1445
believe me if I have the knowledge to fix it I will..... sorry for my bad English.
#1446
question what's the length of the universal shaft for the ta03f any interchange with other cars?
#1447
CC-01 and TA-02 will fit. Stay away from the GPM alloy universals though unless you're putting them in the rear.
#1448
lucky me I just receive a set of titanium suspencion shafts
I am triying to get it under 4 pounds
I am triying to get it under 4 pounds
#1449
Tech Regular
iTrader: (5)
http://www.tamiyaclub.com/forum/inde...c=70807&page=6
but you should buy from irockflipflops, he has the tub, belt, and brace for the same price I paid for just a new belt (aftermarket belt...). If I had seen this thread, I'd've bought them from him. PM me if you have questions.
I'm building a TA03R-S (from a TA03R) for the re-released Lancia 037 Rally. I'm also considering copying the shell in fiberglass (maybe lexan too). Because: Racecar!
#1450
Tech Champion
iTrader: (94)
According to the kids tamiya club it's 175teeth and 525mm long x 4mm wide.
http://www.tamiyaclub.com/forum/inde...c=70807&page=6
but you should buy from irockflipflops, he has the tub, belt, and brace for the same price I paid for just a new belt (aftermarket belt...). If I had seen this thread, I'd've bought them from him. PM me if you have questions.
I'm building a TA03R-S (from a TA03R) for the re-released Lancia 037 Rally. I'm also considering copying the shell in fiberglass (maybe lexan too). Because: Racecar!
http://www.tamiyaclub.com/forum/inde...c=70807&page=6
but you should buy from irockflipflops, he has the tub, belt, and brace for the same price I paid for just a new belt (aftermarket belt...). If I had seen this thread, I'd've bought them from him. PM me if you have questions.
I'm building a TA03R-S (from a TA03R) for the re-released Lancia 037 Rally. I'm also considering copying the shell in fiberglass (maybe lexan too). Because: Racecar!
one roll over and that painted ABS is not going to look so nice
#1451
Tech Regular
iTrader: (5)
By then I'll have taken some touring car, removed the fwd portion (RWD rocks), and shortened the decks :-)
Last edited by firefoxussr; 01-22-2014 at 06:55 PM.
#1452
Ta03f
I am looking for the carbon steering bar anyone????
#1454
long time no see nothing new????
long time don't see nothing new
#1455
Tech Regular
iTrader: (5)
That's how it is for us vets. Subscribe to the thread.
I just sold off my Sprint 2 so i could focus on my F103/TA03RS/Cup Racer.
So what's the word on brushless sensored motors for the TA03 (RS config)?
i'm probably just going to 'use up' the silvercan w/my old HPI brushed esc first... but still i want to know.
I just sold off my Sprint 2 so i could focus on my F103/TA03RS/Cup Racer.
So what's the word on brushless sensored motors for the TA03 (RS config)?
i'm probably just going to 'use up' the silvercan w/my old HPI brushed esc first... but still i want to know.