Tamiya TRF415
It's 1.0mm
Tech Adept
thank you Eirik
Tech Master
iTrader: (1)
Switch pullys!
Can anybody give me a parts list of everything I will need to convert my MSX pullys to the white delrin TA05 pullys, including the center pully. Or do I have to wait for Tamiya to start selling spare parts for the MRE?
Thanks in advance!
Thanks in advance!
Tech Elite
iTrader: (18)
Thats an easy one. Your looking for just the pulleys. If your looking for the MRE centre, i think youd be better off waiting for the MRE all in one alloy centre setup. Very light weight and looks awesome. Just a quick look between my MSX and MRE and looks like it should be a direct swap. You can get the TA05 centre setup if you need it now tho. I dont think Tamiya has released the centre alloy mount as a hopup yet. I know they have both the one way and the ball diff MRE pulleys (which are different to the TA05 pulleys) I love the dirt cover on the MRE diff pulley too!
for the MRE part#'s check the pdf Harshguy posted a few pages back..
You can run the MRE center shaft and pulleys and front and rear pulleys on the MSX ..I ran them fine on mine with the stock white belts..It def works better than the conversion center from the ta-05 we used to run...
You can run the MRE center shaft and pulleys and front and rear pulleys on the MSX ..I ran them fine on mine with the stock white belts..It def works better than the conversion center from the ta-05 we used to run...
Tech Master
iTrader: (1)
RE: PULLY CONV>
JayL>Tamiya is already selling parts for the MRE?
axle> What diff covers? Tamiya has diff covers or is it
an aftermarket part your referring to?
axle> What diff covers? Tamiya has diff covers or is it
an aftermarket part your referring to?
Last edited by maxepower; 09-07-2006 at 11:10 AM.
Tech Champion
iTrader: (4)
Originally Posted by maxepower
JayL>Tamiya is already selling parts for the MRE?
axle> What diff covers? Tamiya has diff covers or is it
an aftermarket part your referring to?
axle> What diff covers? Tamiya has diff covers or is it
an aftermarket part your referring to?
Champ has parts for the MRE in stock already.
HiH
Ed
Tech Master
iTrader: (1)
Part#s
Originally Posted by TryHard
The Rear diff pulley has a lip on it that is very close to the outdrives, effectively covering the diff plates and balls. Also it use 9 3mm balls verus the 8 of the 05 or MSX...
Champ has parts for the MRE in stock already.
HiH
Ed
Champ has parts for the MRE in stock already.
HiH
Ed
That way I can e-mail RC champ with part#s of what I need.
Thanks
Tech Elite
iTrader: (18)
Originally Posted by TryHard
The Rear diff pulley has a lip on it that is very close to the outdrives, effectively covering the diff plates and balls. Also it use 9 3mm balls verus the 8 of the 05 or MSX...
Champ has parts for the MRE in stock already.
HiH
Ed
Champ has parts for the MRE in stock already.
HiH
Ed
Tech Champion
iTrader: (4)
Originally Posted by maxepower
TryHard> you wouldn't happen to have a PDF file on your website for MRE parts?
That way I can e-mail RC champ with part#s of what I need.
Thanks
That way I can e-mail RC champ with part#s of what I need.
Thanks
TAM3454395 Direct centre shaft )one piece layshaft/mount)
TAM9804263 Aluminium Bearing Holder
TAM51213 16t plastic pulley x2
TAM50589 5mm E-Ring Clip
Parts for Rear Diff
TAM53935 Ball Diff Pulley (36t or 18t pulley, which way you look at it)
(all other parts as per MSX, bar 9 diff balls)
Parts for Front Axle
TAM53936 Front One Way Pulley (36t or 18t pulley, which way you look at it)
TAM3454401 Direct Holder (Front Spool)
TAM9804268 Direct Cup (Delrin drive Cup)
TAM9804267 Direct Coupling (Alu Drive cup sleave)
HiH
Ed
Tech Elite
iTrader: (18)
Ed, are you sure that the alloy bearing holders for the centre will work on an MSX? I think you will need the new centre top plate, as it isnt flat, it takes the new bearing holders. I was going to look into these parts also when the MRE has been around a little longer, so i can update my MSX a little.
Tech Champion
iTrader: (4)
Originally Posted by axle182
Ed, are you sure that the alloy bearing holders for the centre will work on an MSX? I think you will need the new centre top plate, as it isnt flat, it takes the new bearing holders. I was going to look into these parts also when the MRE has been around a little longer, so i can update my MSX a little.
IF you don't want to get the new top deck, you just need to reverse the position of the other current bearing holders, making the bearings face inwards.
HiH
Ed
Tech Master
iTrader: (1)
RE:Pully conversion
Originally Posted by TryHard
Parts for the centre pulley;
TAM3454395 Direct centre shaft )one piece layshaft/mount)
TAM9804263 Aluminium Bearing Holder
TAM51213 16t plastic pulley x2
TAM50589 5mm E-Ring Clip
Parts for Rear Diff
TAM53935 Ball Diff Pulley (36t or 18t pulley, which way you look at it)
(all other parts as per MSX, bar 9 diff balls)
Parts for Front Axle
TAM53936 Front One Way Pulley (36t or 18t pulley, which way you look at it)
TAM3454401 Direct Holder (Front Spool)
TAM9804268 Direct Cup (Delrin drive Cup)
TAM9804267 Direct Coupling (Alu Drive cup sleave
HiH
Ed
TAM3454395 Direct centre shaft )one piece layshaft/mount)
TAM9804263 Aluminium Bearing Holder
TAM51213 16t plastic pulley x2
TAM50589 5mm E-Ring Clip
Parts for Rear Diff
TAM53935 Ball Diff Pulley (36t or 18t pulley, which way you look at it)
(all other parts as per MSX, bar 9 diff balls)
Parts for Front Axle
TAM53936 Front One Way Pulley (36t or 18t pulley, which way you look at it)
TAM3454401 Direct Holder (Front Spool)
TAM9804268 Direct Cup (Delrin drive Cup)
TAM9804267 Direct Coupling (Alu Drive cup sleave
HiH
Ed
Is it true the new belts for the MRE are one tooth longer than the MSX. Plus, I heard the teeth on the pully are a new design.
Again,
Thanks
Tech Fanatic
iTrader: (2)
will the front ball diff outdrives for the msx work with the new pulleys on the mre. thanx
Tech Master
iTrader: (1)
RE:Pully conversion
Originally Posted by xtrememadness
will the front ball diff outdrives for the msx work with the new pulleys on the mre. thanx