Tekin RS ESC sensored
Tech Rookie
Hello
What's the average 10.5 tc setup ?
thank
What's the average 10.5 tc setup ?
thank
Good morning,
we run "N" 17.5 motors in our sedan class (by rules), I have the endbell timing set at 45, RS speedo in spec mode,
Brake 100%
Drag brake 20
No Boost
No turbo
Throttle profile 3
Current limiter None
Here is my problem:
I upped the endbell timing to 45 (before it was 30, with a 53 pinion), I do a 5min with a 50 pinion and get off at 172 degrees wich is too much, but I did apply the 1 tooth per 5 degrees of timing recommendation.
I then go down to a 47 pinion and get off the track after 5 minutes at 175 degrees ?????
I don't understand, I went down 6 teeth and it still overheats!
Thanks for the help
we run "N" 17.5 motors in our sedan class (by rules), I have the endbell timing set at 45, RS speedo in spec mode,
Brake 100%
Drag brake 20
No Boost
No turbo
Throttle profile 3
Current limiter None
Here is my problem:
I upped the endbell timing to 45 (before it was 30, with a 53 pinion), I do a 5min with a 50 pinion and get off at 172 degrees wich is too much, but I did apply the 1 tooth per 5 degrees of timing recommendation.
I then go down to a 47 pinion and get off the track after 5 minutes at 175 degrees ?????
I don't understand, I went down 6 teeth and it still overheats!
Thanks for the help
Any one know if there are plans to bring the hotwire interface out for the MacOS ?
Tech Champion
That's for that 10.5 SC setup Randy...it seemed to run quite well today in my SC10. I geared it more for our shorter track but other than that I used the same setup. The truck itself still needs some work to get balanced out but the power definately wasn't holding it back. Truck felt great with my 3800mah practice pack but not so good with the 5000mah pack I use for racing. I think I'm going to have to work on battery placement some to get a better balance overall.
Tech Apprentice
Tech Apprentice
Hi
I experiencing a lack of punch off the grid, simular to what the GM esc's experience. I run a 13.5 redine motor it does it, I run a Duo 2 and it does it. I have reset my Helios 10 handset with 90% epa to the esc then turned it up to 110% and still it happens
Any help would be appreciated.
Cheers Malc
I experiencing a lack of punch off the grid, simular to what the GM esc's experience. I run a 13.5 redine motor it does it, I run a Duo 2 and it does it. I have reset my Helios 10 handset with 90% epa to the esc then turned it up to 110% and still it happens
Any help would be appreciated.
Cheers Malc
Tech Elite
iTrader: (44)
Tech Lord
iTrader: (103)
Hi
I experiencing a lack of punch off the grid, simular to what the GM esc's experience. I run a 13.5 redine motor it does it, I run a Duo 2 and it does it. I have reset my Helios 10 handset with 90% epa to the esc then turned it up to 110% and still it happens
Any help would be appreciated.
Cheers Malc
I experiencing a lack of punch off the grid, simular to what the GM esc's experience. I run a 13.5 redine motor it does it, I run a Duo 2 and it does it. I have reset my Helios 10 handset with 90% epa to the esc then turned it up to 110% and still it happens
Any help would be appreciated.
Cheers Malc
Tech Master
iTrader: (42)
I thought we'd have a smart phone compatible hot-wire program by now. What's up Tekin?
Tech Master
iTrader: (9)
now that would be awesome
Tech Master
iTrader: (1)
They have that already. When you install it, you select the minimal install. I can't remember exactly how it's worded, but there are 2 options. One says something like "full install (recommended)" and then the option below that is the lite version without the goofy looking interface.