Hey Doug, what version E4 you running? I'm lookingto get one of the battery mounts a my lipo's don't fit. i've shimmed the op deck, but i'm not keen to hackat the aluminium parts, any chance you could post a pic of your car with the mount ad lipo installed.
thanks
Pete

Finaly:sneaky:...the car is done...have a Ko 2413 here to..

Lightweight spool by JP-Products
Xray Shafts around
TC SPEC
4.5
Teambrood and TSR cells


Special belt´s wider then the "wide".. this one fill up the whloe pulley..no slip here..

Front:

http://i123.photobucket.com/albums/o...4/S5031386.jpg

http://i123.photobucket.com/albums/o...4/S5031388.jpg


Rear

http://i123.photobucket.com/albums/o...4/S5031389.jpg

This spool, look good, :), Thomas. what belts are this? what brand? .

I´m wait for a FS version of E4, i think make a similar version how Wolfhobbies version, with the chassis of FS, and other parts from the RS version, Top deck, rear whisbones,...

Greetings, Luis C.

Hi Luic, to be honest i do not know. i Bought them from a friend, that have been to a company that makes rubber gaskets,belts etc... it rolls a little slower, but propp will loosen up in time..:lol:

but i can check this out, or maybe fix some..cant promise, but il see what i can do ?

Most stick and lipo packs can be used. It's the best handling EP at the market.

spur/pinon
 

hey guys,
i've just finished building my E4 and i want to bolt a brushless 17.5 (Australian Stock) in. Just wondering if any one has recommendation for a spur and pinon in 48pitch to get me started??

thanks
Prime.

i would like to know to. i bought one of these and it doesnt fit around the dimples in the chassis that stick out towards the center of the car. and at 70 bucks a pop i shouldnt have dremmel slots into the side of it. i dont want to have to grind on my chassis either. do the newer versions of the e4 have these dimples in them? look at the bat tray if you dont understand what im saying. if you look at the top if it has a dimple on each side to fit past the the sides. look at the pic below and you will see.

hey guy's I'm comtenplating on swicthing rides. just curious what everyone opinion on this car. what are the main parts needed for spares. I read somewhere lipos don't fit(might be one brand). If i did go with this I would go with the asphalt spool version.

cheers.

The original E4 Has to be modified to fit Lipos However the newer versions RS and FS Do not need to be modified you just need to use the shims which come with the kit.

i am selling my TM E4 RS version if you are interested look at my signature there is a link there

I thought lipos are not allowed in races as it's considered illegal.

E4FS
 

Have a E4 FS for sale, ran a few times, like twice on carpet, and one day on asphalt, like new. have it in the case at my LHS for sale 175.00

PM me if interested

Mike

TQ and second place at the french regional

http://teammagice4.blogspot.com/

e4
 

u have a older version i run the e4fsc1 and it does not have any dimples in the chassis as i wrote u in the email i would dremal the humps down cause it make the car make weight and help with the handeling . fits all the e4 cars i have seen out here i have sold a few of these trays with no problems with fit and or finish and the cost is cause when you are not getting them made in china and only getting 20 made at a time they cost alot if you are not happy call me like i stated in the e mail and we can fix the problem

got it figured out. just a little mod needed:D i do have the original version and hes right. this tray is awesome guys do not hesitateto buy one. the only thing i say is beware of the size of your lipo as all of them will not fit.:cry: but ive got another on the way and ill post a pic wheni get it done and you guys can see:D

5 cell Brushless Tarmac Setup needed
 

I love this car but am struggling a little with a Outdoor Tarmac setup for 5 cell brushless class.

I find the car oversteers in the slower tight corners, any idea?

Anyone have a setup they can send me please.

Many Thanks


Anthony :cool:

there are a couple of set ups that i posted a while back , try any of those they worked great!! where is your battery located? when i ran 5 cells i had them all the way foward.or you can split them up too, 3 foward and 2 back or 1 and 4 and so on.

not a little mod as i first thought. the tray winds up being a little long and is taking some dremmiling and fitting to get it to work. this tray does not fit well in the original e4. so check before you buy. 70 is alot for something you have to make fit:cry:

Just woundering how you do the xray front uni mod?

Hi, I bought a second hand E4 just after christmas. I have now got to the point where two shocks are knackered. Both caps were mismanufactured and the orange bladder required cutting to thin the edge down so I could even get the threads to start.

Anyway I dislike the shocks and would like to buy some new (better) ones. Can someone please point me in the direction of a shop, preferably UK but not a requirement where I can buy the K factory LX shocks. Of course I am assuming they are the best, if Tamiya TRF shocks fit then they are of course another option.

What is the best shock option and where can I get them from. Cheers. Jonathan

E4JS how ?

e4 lipo
 

E4 , RS & FS can't use Orion 25C 3600mah & 30C 3800mah battery !

E4FS, E4RS, E4JS & E4JR can use most Lipo.

you can fit the 5000 lipos if you shim the top deck 3mm:)

hi all, my car should come in sometime next week, but I had a question about the stock 110T spur gear. Is it metric, like Tamiya spur/pinions? The reason I ask is because i have lots of RRP 64p pinion gears. And if it is, rather than buying metric pinions I was just gonna swap out the spur, thanks for your time, and I cant wait till my LHS gets my car in :sweat:

They're 64p

awesome, thanks for the quick reply :)

Support Orion 3800MAH 30C ?

don't get this lipo yet, but the spec sheet shows it's quite wide. E4JS & E4JR should be no problem. Not sure about E4FS & E4RS yet.

I was prepping my E4 last night in an attempt to run it for the 1st time this weekend and noticed that the bar where the sway bars slot into seems to move at one side, which in turn makes one side of the sway bar more responsive than the other and therefore stiffer which must effect the handling. Is this normal? or if not how have you guy's fixed the problem.

It does this at both ends, it's the bar mounted to the bulkheads. From looking at it it will make cornering one way different to the other.

Cheers
Aaron

there is an adjustment screw in the mounting braket that you need to adjust on both sides to get the same feel.

what are your guys thoughts on this car for asphalt racing looking at 10.5 brushless? any thing i should know before investing in this car? thanks in advance.

The car has a ton of steering and carries alot of corner speed, i was very happy with the car :)

Hey what shop do have it for sale at?

AWESOME PAINT JOB
 

Yeah i love the paint job to. I want one for my nitro G4

Hi I was looking into getting an e4, but I dont know what to buy. I run rubber asphalt in the summer and carpet foam in the winter. I also run trakpower 4900 lipos. Which model will be the best for me. Also I do not like running a spool or oneway.
How do the a arms hold up? I looked at the chasis over the weekend and that was the only thing that I saw on the car that looked weak at first glance.

The arms hold up very well , i would get the FS version is for foam but it works very well on asphalt. You should be able to fit the lipo in it if not all you need to do is to shim up the top deck for the battery to fit. Also the FS comes with a front diff.

Anyone know if its possible to get 0deg rear toe on the E4?
I'm using the car in a silvercan class and don't need rear toe as the engine doesnt have enough power to require it.

Cheers
Lycan

Lycan,You can get the 1.5 k factory rear hub carriers and put them on backwerds to get 0,you must set the rear toe blocks to 1.5 to do this.Hope this helps.Doug Lemmons

FYI

The new Intellect 3800 hard case Lipos fit my E4.

Just needed to drill a hole in the back end of the top deck so that I could plug the negative wire into the battery. It doesn't appear to weaken the top deck but means I can't mount my cooling fan there anymore.