T.O.P. Racing "Scythe" 1/10 EP Touring Car
#1338
Tech Master
iTrader: (21)
O.K.,need a hand.Just got hold of a Trinity Duo 17.5.Could use a little direction.Running on a smallish carpet track,Foams.Any direction on rollout?Thanks.George,did you run the car at 360 race.If so,how did it work out?Couldnt make it down(work).Will try to make it down for a race sometime in the near future.Mario.
#1339
O.K.,need a hand.Just got hold of a Trinity Duo 17.5.Could use a little direction.Running on a smallish carpet track,Foams.Any direction on rollout?Thanks.George,did you run the car at 360 race.If so,how did it work out?Couldnt make it down(work).Will try to make it down for a race sometime in the near future.Mario.
#1340
#1341
O.K.,need a hand.Just got hold of a Trinity Duo 17.5.Could use a little direction.Running on a smallish carpet track,Foams.Any direction on rollout?Thanks.George,did you run the car at 360 race.If so,how did it work out?Couldnt make it down(work).Will try to make it down for a race sometime in the near future.Mario.
will do EJ thanks
#1343
have you run a 13.5 with the car yet if so gear the same and get the temp from there
#1344
Tech Master
iTrader: (21)
..............
Just got home.Up until this season,my LHS ran handout stock brushed motors.We finally can run brushless.Lipo too,until,as the owner says,the first fire.lol. I have read/been told 4-5 to 1 gear ratio/50mm rollout.Will get to run sunday so.......EJ,how are ya? Yes,post it if you think it'll be helpful.it is a work in progress at the moment but,works fine so far.Thanks.Mario.
#1345
What can be used as a good base/starting setup for rubber-asphalt racing with spool upfront and ball-diff at the rear ???
#1346
Tech Adept
Hello Top Racers ,i leave with you here, some setups and summary of the Spanish National , in addition to pictures of my new chassis, and more information about our car,sorry this in Spanish, but google is a wonderful tool.
- National:
http://www.technicalrp.com/minizforu...edo-t3747.html
- Setups:
http://www.technicalrp.com/minizforum/setups-t3740.html
- New car (ARP):
http://www.technicalrp.com/minizforu...trp-t3628.html
Thank you very much for all the information and ideas that you have shared and which have undoubtedly helped many pilots like me.
Greetings, Luis C.
- National:
http://www.technicalrp.com/minizforu...edo-t3747.html
- Setups:
http://www.technicalrp.com/minizforum/setups-t3740.html
- New car (ARP):
http://www.technicalrp.com/minizforu...trp-t3628.html
Thank you very much for all the information and ideas that you have shared and which have undoubtedly helped many pilots like me.
Greetings, Luis C.
#1347
hey all: I read on hear that barry baker has split fro team magic and some one suggested he join top racing. While i think that would be great for the top team i think barry is not going to just jump into the next situation that comes along unless he knows he has some team driver or other job security with that company? Just my thoughts thanks
#1348
Tech Master
Tomorrow i have my own Scythe again finaly.
I have a question. i the last link that is posted by Luic i see a Scythe with a difrend top plate and difrend top bulkheads. Is this self made or not?
I was thinking to divide the top bulkheads so i have more flex.
I have a question. i the last link that is posted by Luic i see a Scythe with a difrend top plate and difrend top bulkheads. Is this self made or not?
I was thinking to divide the top bulkheads so i have more flex.
#1349
Tech Adept
Yes Mikky32, is handmade top deck and cut bulkheads in the Scythe 08 car, in the left of photo, the right car is ARP without mods.
More flex and easy for work in it. In rain i add a composite down bulkheads and the center part of motor mount in composite, too.
Greetings, Luis C.
More flex and easy for work in it. In rain i add a composite down bulkheads and the center part of motor mount in composite, too.
Greetings, Luis C.
#1350
Tech Master
Luic dit it inprofe the handling and corner speed?
I want to do the same with the topbulkheads and make the rest all allu just like the arp.
I want to do the same with the topbulkheads and make the rest all allu just like the arp.