|
ok, lets think about this.
1) take wheel off and feel for it 2) take hex off and feel for it 3) take the pin out and feel for it 4) take the bearing outs and feel them. Start from the outside and work your way in. |
Oke, I'll do that.
While I was spinning the wheel, I noticed this: quality sucks, because youtube is still processing it.. http://www.youtube.com/watch?v=gS-KYbYxgII It's like there is some kind of play on the axle and inner ring of bearing. |
Originally Posted by Wildcat1971
(Post 12427119)
ok, lets think about this.
1) take wheel off and feel for it 2) take hex off and feel for it 3) take the pin out and feel for it 4) take the bearing outs and feel them. Start from the outside and work your way in. I can feel it 2) take hex off and feel for it Still there.. 3) take the pin out and feel for it Still there.. 4) take the bearing outs and feel them. Feel like brand new bearing, which they are. |
Originally Posted by D.Martijn
(Post 12427146)
1) take wheel off and feel for it
I can feel it 2) take hex off and feel for it Still there.. 3) take the pin out and feel for it Still there.. 4) take the bearing outs and feel them. Feel like brand new bearing, which they are. |
Originally Posted by derbrylac
(Post 12427198)
replace hub??
Still pretty new. also, the bearings fit snug so I think thats not the problem. |
What is a proper gearing for the buggy with a 7.5sensored motor?!
|
how much kv?
|
Originally Posted by D.Martijn
(Post 12427090)
Hey guys,
Anyone there that also runs the Jconcepts axles?? I recently fitted them and it seems there is a clicking noise.. I fitted new bearings and it's the same.. Any suggestions to solve the clicking.. it's driving me insane that stupid noise.. http://www.youtube.com/watch?v=rWLTbV2gLuk I also posted a message in the Jconcepts thread a few days ago but haven't gotten an answer yet.. since there is a race sunday, I want to get it fixed asap. |
Originally Posted by Matt Trimmings
(Post 12427288)
I only use 1 shim per axle instead of the 2.
And there will be a tad more clearance at the little notch, I'll might try to do that. Thanks |
Originally Posted by theblitzkidd
(Post 12427256)
What is a proper gearing for the buggy with a 7.5sensored motor?!
|
Originally Posted by D.Martijn
(Post 12427293)
So you can move the axle more towards the outside of the buggy?
And there will be a tad more clearance at the little notch, I'll might try to do that. Thanks |
Originally Posted by Wattsup23
(Post 12427303)
start around 78/22 then gear from there
|
Originally Posted by D.Martijn
(Post 12427146)
1) take wheel off and feel for it
I can feel it 2) take hex off and feel for it Still there.. 3) take the pin out and feel for it Still there.. 4) take the bearing outs and feel them. Feel like brand new bearing, which they are. |
Originally Posted by Bubonic-X
(Post 12427388)
How about this keep it lubed..... Does the car do anything wierd when your driving it and you cant feel it when your driving right? If it still spins free just drive it. Sometimes it goes away when after some club racing but its not affecting your car... It does not seem like the axles are the problem. If its the bearing it will eventually get worse and come apart. I bet when you put the wheel on it spins free and comes to a slow stop. If its going clunk clunk as its spinning it cant be the axle. most likely the bearing
I'm going to look further into it in the eve. |
Do the yaiba hubs develope slop like the blue ae hubs?
|
| All times are GMT -7. It is currently 03:20 PM. |
Powered By: vBulletin v3.9.3.9 Patch Level 3
Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.