R/C Tech Forums - RC10B4.1 FT/WC

Hey guys.

Finally got my whole new electronics setup in.

I just want a few tips to make it look better.

Where is a good place for the capacitor?
Right now I just tucked it behind the ESC.

Anything helps. Eventually I will black out the wires but I want it to look good for now.

Thanks!

Venom1836

12-26-2012 03:43 PM

Well I cleaned up the receiver side and now all I need is that wire wrap that it seems AMainHobbies does not carry anymore...

Where can I get it???

Any tips on what I should do to the ESC side?

I already have some black motor wires, I just dont want to take the risk of soldering them onto the ESC yet...

YankeeFan123

12-26-2012 03:54 PM

Quote:

Originally Posted by Venom1836 (Post 11597376)

If you don't want to risk soldering you can use sharpie if you would like.

And since I run my LRP all the way back I put the capacitor on the side, but it's all personal preference, it looks good where it is

mtpocketsracing

12-26-2012 03:57 PM

Quote:

Originally Posted by associatevalley (Post 11596185)

My cars including my 1/8th buggy are 90% ss and 10% titanium. I'd love to be able to get them all in one kit. I know the numbers say ss isn't as strong as stock steel but I've never had a ss failure with some basic placement prejudice.

Acer bearing company sells top grade titanium

ss is generally soft. especially the grade they use for screws.
you need a really good set of wrenches that fit ultra snug. I don't see the gained benefit of the more expensive ss screws for a rc car.

Venom1836

12-26-2012 04:05 PM

Quote:

Originally Posted by YankeeFan123 (Post 11597420)

What happens if I remove the cap?

What if I remove it but replace it with the LRP Works Cap Pack?

Jmuck69

12-26-2012 04:15 PM

Quote:

Originally Posted by Venom1836 (Post 11597458)

What happens if I remove the cap?

What if I remove it but replace it with the LRP Works Cap Pack?

Replace it with the LRP Works Cap and secure it next to the ESC.

Jmuck69

12-26-2012 04:19 PM

Quote:

Originally Posted by Venom1836 (Post 11597250)

I like to coil the transponder and servo wires around a screwdriver shaft. Wrap tightly and hold for a minute and they will stay that way. No need to bundle and gather in shrink tubing.

5th wheel

12-26-2012 05:39 PM

Is 91175 the part number for the vts for the b4.1.and does anyone know if it will fit under the rpm dust cover.and is it worth buying.I am new to the buggy stuff and still learning how to do setups.thanks

Millerracing

12-26-2012 05:46 PM

Quote:

Originally Posted by 5th wheel (Post 11597723)

No it will not fit under the rpm gear cover

Wildcat1971

12-26-2012 05:51 PM

Quote:

Originally Posted by 5th wheel (Post 11597723)

no it will not. But it will fit under the AE cover.

5th wheel

12-26-2012 06:15 PM

Quote:

Originally Posted by Wildcat1971 (Post 11597761)

no it will not. But it will fit under the AE cover.

Ok thanks guys do I need anything else to go with it..91175 vts.but it does not say anything about that it will fit the b4.1..do you guys know if the avid will fit under the rpm dust cover.thanks for the information and help..:tire::)

aeMatt

12-26-2012 06:15 PM

2 Attachment(s)

Venom, check out these pictures of my car for some wiring ideas :)

Wildcat1971

12-26-2012 06:19 PM

yes, the avid will fit

All times are GMT -7. It is currently 09:14 PM.

Page 1754 of 1914

« First

754

1254