Kyosho Lazer ZX5 FS/FS2 Thread
#751
R/C Tech Elite Member
iTrader: (520)
What do you guys use to hold your diff rings when you sand them? Of all my cars, my zx5 goes through more diffs than any other car. It's the biggest pain in the ass because I can use the out drives to sand the rings. So I end up using my fingers. I think I'm starting to loose my finger prints. I picked up the yeah racing diff tool, but the ring doesn't sit flat on it.
Any tips?
Any tips?
If you guys know anyone looking for a lazer and a lot of parts-I am thinking about selling mine..
#752
Hey Guys,
I recently purchased a FS2 and a full set of big bores. Im gonna run the Jared Tebo setup and was wondering if I need to purchase any additional parts before the build for these shocks to work, or parts for the Tebo build.
I see there is a 4th hole used on the front shock stay, is it just drilled? or can I buy one with this hole?
also whats a good gearing start point with an 8.5 turn brushless?
thanks!!!
I recently purchased a FS2 and a full set of big bores. Im gonna run the Jared Tebo setup and was wondering if I need to purchase any additional parts before the build for these shocks to work, or parts for the Tebo build.
I see there is a 4th hole used on the front shock stay, is it just drilled? or can I buy one with this hole?
also whats a good gearing start point with an 8.5 turn brushless?
thanks!!!
#754
Hey Guys,
I recently purchased a FS2 and a full set of big bores. Im gonna run the Jared Tebo setup and was wondering if I need to purchase any additional parts before the build for these shocks to work, or parts for the Tebo build.
I see there is a 4th hole used on the front shock stay, is it just drilled? or can I buy one with this hole?
also whats a good gearing start point with an 8.5 turn brushless?
thanks!!!
I recently purchased a FS2 and a full set of big bores. Im gonna run the Jared Tebo setup and was wondering if I need to purchase any additional parts before the build for these shocks to work, or parts for the Tebo build.
I see there is a 4th hole used on the front shock stay, is it just drilled? or can I buy one with this hole?
also whats a good gearing start point with an 8.5 turn brushless?
thanks!!!
#756
most people at my track run 35 front and 30 rear.. the short tops are for the Lazer.. the long for the RB5
#757
here is the latest pic of my fs2. enjoy and once again thank you for all the help!!
[IMG][/IMG]
[IMG][/IMG]
#758
Hello guys
I just got a RTR Lazer ZX5. Just wondering if this part will fit the car?
KYOW5194V - Kyosho Front Velvet Coated Triple Cap Threaded Shock Set
KYOW5195V - Kyosho Rear Velvet Coated Triple Cap Threaded Shock Set
Thanks
Regards
calvin
I just got a RTR Lazer ZX5. Just wondering if this part will fit the car?
KYOW5194V - Kyosho Front Velvet Coated Triple Cap Threaded Shock Set
KYOW5195V - Kyosho Rear Velvet Coated Triple Cap Threaded Shock Set
Thanks
Regards
calvin
#759
To my knowledge, they will fit.
#760
Tech Rookie
I just picked up a ZX-5 kit NIB for $40 off craig's list. What parts need upgrades for durability? Thanks for the help.
#762
Tech Rookie
good question. I'm not really sure. It looks like the guy had it for awhile. It's in a red box that says zx-5. no fs or sp so it must be older. But everything is still in plastic bags and sealed.
#765