Durango DEX210 Thread
#2881
Tech Elite
iTrader: (79)
If by stock spec you mean blinky mode......
For blinky mode I am at 34/75 to 35/75 dependent on the layout.
Rs in blinky, Fantom Apex (revtech) with 12.5mm spec high torque rotor, 4th timing line on the motor.
The 34 might fit with the 75, for the 35 you have to lengthen the motor screw holes and make an "adjustment" to the gear cover.
Dayton
For blinky mode I am at 34/75 to 35/75 dependent on the layout.
Rs in blinky, Fantom Apex (revtech) with 12.5mm spec high torque rotor, 4th timing line on the motor.
The 34 might fit with the 75, for the 35 you have to lengthen the motor screw holes and make an "adjustment" to the gear cover.
Dayton
#2882
Ran the DEX210 for the 1st time last night... heck 1st time ive ran a 2wd buggy...LOL... So really dont have anything to compare to
Thing was DIALED.... Used Billy F setup and seemed preety good... had ta stiffen rear shock since the CORRECT springs arent out yet.... most the b4.1 guys where very impressed with it, not me but It, LOL
I Do have a question...
The drive Cups seem pretty sloppy where the dog Bone Goes In, meaning, The move in and out at the bearings at the upright.... i was afraid the Pins on the axle would fall out...
I placed a Little piece of Fuel tiding inside the cup to help tighten it up... but those fell out..
Did i miss something in the Manual???
Thanks guys
GREAT rig... cant wait ta get some more Runtime in it... Also ordered RW RC spurs and emailed for dealer account..... SWEET!!!
Stav
Thing was DIALED.... Used Billy F setup and seemed preety good... had ta stiffen rear shock since the CORRECT springs arent out yet.... most the b4.1 guys where very impressed with it, not me but It, LOL
I Do have a question...
The drive Cups seem pretty sloppy where the dog Bone Goes In, meaning, The move in and out at the bearings at the upright.... i was afraid the Pins on the axle would fall out...
I placed a Little piece of Fuel tiding inside the cup to help tighten it up... but those fell out..
Did i miss something in the Manual???
Thanks guys
GREAT rig... cant wait ta get some more Runtime in it... Also ordered RW RC spurs and emailed for dealer account..... SWEET!!!
Stav
#2883
Tech Champion
iTrader: (94)
If by stock spec you mean blinky mode......
For blinky mode I am at 34/75 to 35/75 dependent on the layout.
Rs in blinky, Fantom Apex (revtech) with 12.5mm spec high torque rotor, 4th timing line on the motor.
The 34 might fit with the 75, for the 35 you have to lengthen the motor screw holes and make an "adjustment" to the gear cover.
Dayton
For blinky mode I am at 34/75 to 35/75 dependent on the layout.
Rs in blinky, Fantom Apex (revtech) with 12.5mm spec high torque rotor, 4th timing line on the motor.
The 34 might fit with the 75, for the 35 you have to lengthen the motor screw holes and make an "adjustment" to the gear cover.
Dayton
#2885
may try that for now till Opt springs are available
#2887
Tech Master
iTrader: (77)
3/3 toe block
I finished up a batch of toe blocks. I have a limited quantity since I had a bunch of pre-orders. They are CNC machined from 7075/T651 aluminum. It is superior to 2024 or 6061. PM me and I will give you a price. I will fill in order that PMs are received.
The pic of the installed block was the first prototype. The only changes I had to make was a couple cosmetic radii.
The pic of the installed block was the first prototype. The only changes I had to make was a couple cosmetic radii.
#2888
Tech Lord
iTrader: (52)
I finished up a batch of toe blocks. I have a limited quantity since I had a bunch of pre-orders. They are CNC machined from 7075/T651 aluminum. It is superior to 2024 or 6061. PM me and I will give you a price. I will fill in order that PMs are received.
The pic of the installed block was the first prototype. The only changes I had to make was a couple cosmetic radii.
The pic of the installed block was the first prototype. The only changes I had to make was a couple cosmetic radii.
#2891
My DEX210... ready to roll
... last pic shows reinforcement of gearbox using JB wield
... last pic shows reinforcement of gearbox using JB wield
#2892
They just do anti squat... if you take note of the inscription on all three they all say the same "3*" toe-in ......the toe is changed by selecting the appropriate insert in the hubs where it connects to the arm.
#2894
#2895
Tech Regular
iTrader: (4)
Sorry I didn't get my report in. I own the prototype and ran it before full-on production started. I gave Yeti the feedback that the car felt exactly as it did before. Once he got the O.K. he made a whole bunch. This thing is awesome! Installed like a factory piece, except for the fact that the pivot balls fit BETTER than the ones on my 410. Knowing that my car is now bulletproof is also nice. Get your orders in, guys. If you have to wait, wait. Its definitely worth it. If your buddy has a 210, order 2 and save on shipping!