387LikesJConcepts Thread
12-10-2015, 11:59 PM
#8656
Looks like JC is offering many of their new tread designs in 60mm (similar to 2.4, VTR, EVO) for both 2WD and 4WD buggies (e.g. Smoothies and Reflex). Paul replied on a previous page that they're not likely going to release 2.2 Smoothies. While stock guys are definitely running 60mm/2.4, many of the mod guys in 2wd and 4wd are still running 2.2's at my local tracks (OCRC, LRH, etc.). I tracked down Maifield's Surf City OCRC setup and it says he was running 60mm front and 2.2 rear. Odd.
Have people transitioned over to 60mm across the board elsewhere in the U.S.? Just picked up a new wheeler and eyeing some 60mm Bar Flys to run on my 2wd and 4wd buggies though I'll probably be an odd man out. Maybe it's because people run AE or TLR wheels for the most part and stick with the 2.2s?
Have people transitioned over to 60mm across the board elsewhere in the U.S.? Just picked up a new wheeler and eyeing some 60mm Bar Flys to run on my 2wd and 4wd buggies though I'll probably be an odd man out. Maybe it's because people run AE or TLR wheels for the most part and stick with the 2.2s?
12-11-2015, 05:15 AM
#8657
Not at the moment; we will reevaluate once they have all their new kits released and settled back in.
12-11-2015, 06:20 AM
#8658
Has anyone else had issues with the JConcepts Titanium Knurl Tip Front Axle Set? I ordered these along with the Jconcept front hexes and my B5m Lite about 3 weeks ago. From day one, there has always been a gritty feeling on the left side when I hand turn the axles. After each run it gets a little worse. I removed everything multiple times and cleaned them, again same result. I changed the bearing with a brand new bearing, same issue. I switched the axle from the left side of the car to the right and now the right side has a gritty feel to it. It's obviously the axle but can't figure out the problem. I have tried everything I can think of but can't get one side to spin smoothly. These things are not cheap at set At $30. Any ideas?
Thanks
Thanks
12-11-2015, 08:29 AM
#8660
Tech Regular
iTrader: (23)
Hunch,
I'll see you tonight. I had the same issue. I may have a solution.
Eric
I'll see you tonight. I had the same issue. I may have a solution.
Eric
Has anyone else had issues with the JConcepts Titanium Knurl Tip Front Axle Set? I ordered these along with the Jconcept front hexes and my B5m Lite about 3 weeks ago. From day one, there has always been a gritty feeling on the left side when I hand turn the axles. After each run it gets a little worse. I removed everything multiple times and cleaned them, again same result. I changed the bearing with a brand new bearing, same issue. I switched the axle from the left side of the car to the right and now the right side has a gritty feel to it. It's obviously the axle but can't figure out the problem. I have tried everything I can think of but can't get one side to spin smoothly. These things are not cheap at set At $30. Any ideas?
Thanks
Thanks
12-11-2015, 08:42 AM
#8661
Has anyone else had issues with the JConcepts Titanium Knurl Tip Front Axle Set? I ordered these along with the Jconcept front hexes and my B5m Lite about 3 weeks ago. From day one, there has always been a gritty feeling on the left side when I hand turn the axles. After each run it gets a little worse. I removed everything multiple times and cleaned them, again same result. I changed the bearing with a brand new bearing, same issue. I switched the axle from the left side of the car to the right and now the right side has a gritty feel to it. It's obviously the axle but can't figure out the problem. I have tried everything I can think of but can't get one side to spin smoothly. These things are not cheap at set At $30. Any ideas?
Thanks
Thanks
. If indeed you find something wrong with the axle itself, please contact JConcepts directly and we will help anyway possible.
12-11-2015, 10:02 AM
#8662
Thanks for the response, and I thought about the bearing insert, which I did glue. However , when I swapped the axle from one side to the other the problem followed. The other side was smooth. So again I can only guess it's the axle itself.
12-13-2015, 10:08 AM
#8663
Sorry if this has been asked before: Are there already 12 mm front wheels by JConcepts that fit the TLR 22 3.0 and has the same offset, e.g. the ZX-6 front wheels?
12-14-2015, 05:40 AM
#8664
Unfortunately the TLR 2wd offset is different from any other buggy and we only have the standard/original hex wheel.
12-14-2015, 09:07 AM
#8665
12-14-2015, 05:03 PM
#8666
Any idea on a time frame release on the carbon/aluminum setup board you guys are coming out with??
12-15-2015, 05:29 AM
#8668
.
12-15-2015, 11:50 AM
#8669
I see your 60mm wheel for the 22-4 (which I use on the HB D413) is not in stock at your warehouse (nor many other online retailers). Are you discontinuing this item now that TLR has announced the 22-4 61mm? I hope not 
http://www.jconcepts.net/shop/bullet...24-front-wheel
http://www.jconcepts.net/shop/bullet...24-front-wheel
12-15-2015, 12:00 PM
#8670
I see your 60mm wheel for the 22-4 (which I use on the HB D413) is not in stock at your warehouse (nor many other online retailers). Are you discontinuing this item now that TLR has announced the 22-4 61mm? I hope not
http://www.jconcepts.net/shop/bullet...24-front-wheel
http://www.jconcepts.net/shop/bullet...24-front-wheel