JConcepts Thread
#6693
wtf? these tires have only a few runs on them, and I haven't crashed into anything sharp... was there a bad batch of gold barcodes?
#6695
Abuse? Where? it's just mud on the rim, want me to clean it for you?
#6696
Tech Champion
iTrader: (12)
No, mine are just as dirty
No thanks Jeff
Maybe it is just dirt now that you point it out and I zoomed in.
But still the tire could have rubbed a pipe or who knows just right.
CA will fix it. There are guys that cut whole tires to fit different rims and vehicles and glue them back together.
No thanks Jeff
Maybe it is just dirt now that you point it out and I zoomed in.
But still the tire could have rubbed a pipe or who knows just right.
CA will fix it. There are guys that cut whole tires to fit different rims and vehicles and glue them back together.
Last edited by fq06; 11-06-2013 at 05:00 PM.
#6697
Last Jconcepts tires I buy, lol.
I've beat the hell out of prolines and never torn a tire.
I just do not have good luck with Jconcepts...
I've beat the hell out of prolines and never torn a tire.
I just do not have good luck with Jconcepts...
#6699
I'm by no means an amazing driver, but certainly not terrible. If it was from rubbing a pipe, it's pretty disappointing that they're so fragile..
#6700
Tech Master
iTrader: (35)
I have had the same issue, but also with proline, panther, & beta (the sweeps I got recently haven't done it, yet). It happens mostly with my ebug, but it does happen with my 1/10 also. Looking at your tire & wheel, I'm seeing lots of grey clay on the edge of the wheel, but none on the lugnut or axle or middle of the wheel in general. I also notice that you, like myself, are running the open cell inserts. Like mine, It looks like your tire tore rather than the glue coming off. With my situation, & now reinforced by seeing yours, I'm begining to think the problem is to much traction for the insert. I think the tire might be rolling over all the way to the wheel putting huge stress on the area that is glued on. This is where the roll stops & the stretch begins. I'm beging to think we both need to use firmer inserts.
Does this sound like a reasonable hypothesis to any one else?
#6701
Tech Champion
iTrader: (68)
Hideeho
I have had the same issue, but also with proline, panther, & beta (the sweeps I got recently haven't done it, yet). It happens mostly with my ebug, but it does happen with my 1/10 also. Looking at your tire & wheel, I'm seeing lots of grey clay on the edge of the wheel, but none on the lugnut or axle or middle of the wheel in general. I also notice that you, like myself, are running the open cell inserts. Like mine, It looks like your tire tore rather than the glue coming off. With my situation, & now reinforced by seeing yours, I'm begining to think the problem is to much traction for the insert. I think the tire might be rolling over all the way to the wheel putting huge stress on the area that is glued on. This is where the roll stops & the stretch begins. I'm beging to think we both need to use firmer inserts.
Does this sound like a reasonable hypothesis to any one else?
I have had the same issue, but also with proline, panther, & beta (the sweeps I got recently haven't done it, yet). It happens mostly with my ebug, but it does happen with my 1/10 also. Looking at your tire & wheel, I'm seeing lots of grey clay on the edge of the wheel, but none on the lugnut or axle or middle of the wheel in general. I also notice that you, like myself, are running the open cell inserts. Like mine, It looks like your tire tore rather than the glue coming off. With my situation, & now reinforced by seeing yours, I'm begining to think the problem is to much traction for the insert. I think the tire might be rolling over all the way to the wheel putting huge stress on the area that is glued on. This is where the roll stops & the stretch begins. I'm beging to think we both need to use firmer inserts.
Does this sound like a reasonable hypothesis to any one else?
#6702
#6703
Tech Addict
iTrader: (24)
Hideeho
I have had the same issue, but also with proline, panther, & beta (the sweeps I got recently haven't done it, yet). It happens mostly with my ebug, but it does happen with my 1/10 also. Looking at your tire & wheel, I'm seeing lots of grey clay on the edge of the wheel, but none on the lugnut or axle or middle of the wheel in general. I also notice that you, like myself, are running the open cell inserts. Like mine, It looks like your tire tore rather than the glue coming off. With my situation, & now reinforced by seeing yours, I'm begining to think the problem is to much traction for the insert. I think the tire might be rolling over all the way to the wheel putting huge stress on the area that is glued on. This is where the roll stops & the stretch begins. I'm beging to think we both need to use firmer inserts.
Does this sound like a reasonable hypothesis to any one else?
I have had the same issue, but also with proline, panther, & beta (the sweeps I got recently haven't done it, yet). It happens mostly with my ebug, but it does happen with my 1/10 also. Looking at your tire & wheel, I'm seeing lots of grey clay on the edge of the wheel, but none on the lugnut or axle or middle of the wheel in general. I also notice that you, like myself, are running the open cell inserts. Like mine, It looks like your tire tore rather than the glue coming off. With my situation, & now reinforced by seeing yours, I'm begining to think the problem is to much traction for the insert. I think the tire might be rolling over all the way to the wheel putting huge stress on the area that is glued on. This is where the roll stops & the stretch begins. I'm beging to think we both need to use firmer inserts.
Does this sound like a reasonable hypothesis to any one else?