Well there ya go, Flanno made a boo boo ...LOL.

Atleast now we know for sure. :sneaky:

Mark could you give some insight as to when is it good to add a shim i run 1x.2 giving a total of .5 and use 25% nitro with a t3 plug gotech i would like to try a cooler plug t4 soon

Hey matty

its up to you to experiment , i can suggest what some people use but it may not work for your set up. It sounds like you have a good set up as is from our convo yesterday .

BTW MassiveMods Crissy specials up on line , more to come !

www.massivemods.com

Cheers MM

yea no probs mark thanks for your help yesterday :nod:

Hey guys

Heres a nice result from Adam Alexander (RC Hobby Zone/Massive Mods Team driver) with his GX5R powered truggy...

http://www.rctech.net/forum/6712236-post12.html

Cheers

DN

well done Adam ....:nod:....

well this weekend i put my 7 port in along with the 0801 pipe , but i much prefer the 2072 pipe better top end and bottem end just my thoughts after going back to th original and i also much prefer my MG66 to looks like i now have back up motors :lol:

We had our clubs 3 hour Enduro race on Sunday - what a hoot !!
It was hot and dry, with the track being super dusty.
Our team (Team X-Ray-ted) finished a ways down the honours list, but the 4 of us had a great day. We had to bow to more experianced and better drivers, plus a track that definitly suited the truggy teams a lot more than the buggy teams. It got very dusty and bumpy, making the buggy a bit of a handfull over the last couple of hours.
For an Enduro event it was an incredibly close finish. 1st and 2nd place were seperated by only 20 seconds after 3 hours and 214 laps of racing - incredible.
Highlights for me were the fact that the GX-3R in my buggy performed flawlessly all day, never missing a beat. Also, two of the truggies in the winning team were powered by GX-5R's ;)

well gone grizz ... the enduro events are always a blast :D

this weekend for me was nothing but dramas the first to races were faultless then the following 4 nothing but dramas oh well until 2010 will be a hoot :D

Well in a nightmare 2 week holiday visiting the family up in Sydney, which involved the Navarra overheating every time i went up a hill on the drive from Melb to Syd.... head had to be skimmed, 5 valves replaced, new radiatior, new alternator belt, new thermostat...... lots of fun!

I did however get a chance to pull apart the 7 port after my troubles with the carb coming loose a while back, turns out i put the bolt in on the wrong side, as i had reassembled it in a rush so that the motor wasnt sitting open :blush: my bad, wont be doing that again lol.
Got that sorted and took it to the track, loving the car and the motor! Ran really well, but i had to hold back on the tuning as the motor is still a few litres off being able to put a race tune on it. Still heaps of power and speed, so should go like a rocket once it loosens up. Looking forward to getting some more track time hopefully sooner rather than later.

Jeez - bummer with the Navarra, but all smiles with the 7 Port. Just wait until it loosens up fully. You will be a happy camper :)

Buggy Tyre Sale on now !

www.massivemods.com.au


Cheers MM

Dont worry i was very happy with it, and im really looking forward to it loosening up, whether i can even make use of the power will be another story :lol:. Might go to a smaller carb restrictor (stock one atm) once it loosens fully.

6.5 restrictor and you will have power to burn plus good economy.
3 x 1.1mm springs or 2 x 1.1mm and 1 x 1mm springs and 3 x alloys - nice combo on the 7 Port.

What springs come stock with an RC8B??? lol well whatever they are thats what i have on, and the metal shoes that come in the kit.

Will need to check up on the clutch, and i will definately try the 6.5mm restrictor as suggested. :)

Must just make sure i dont have the carb screw in the wrong :p such an idiot lol

hay mark whats the differance between blocks from the mg66 compared to the others i have ?

i had alot of trouble on the weekend and close inspection probably due to a crash the last race meet i have cracked the the block of my MG...

will my other blocks be okey or do i need to use the new gx line ?