Team Losi JRXS Type-R
#8431
Tech Adept
iTrader: (14)
Alright, so building my second jrxs-r. First one I bought used.
Building the diffs, it seems the diff spring is too long. I noticed that it didn't seem right for the thrust bearing to be exposed, tightening one for a while figuring it would collapse the spring, but eventually I heard a loud crack and it didn't compress the spring at all.
Finally took apart a diff from the first car. Comparing the diff springs, the correct one is silver in color, 3 turns in the spring and .267in. The ones I got in this kit are black in color, 4 turns in the spring and .429 in.
Suggestions?
Building the diffs, it seems the diff spring is too long. I noticed that it didn't seem right for the thrust bearing to be exposed, tightening one for a while figuring it would collapse the spring, but eventually I heard a loud crack and it didn't compress the spring at all.
Finally took apart a diff from the first car. Comparing the diff springs, the correct one is silver in color, 3 turns in the spring and .267in. The ones I got in this kit are black in color, 4 turns in the spring and .429 in.
Suggestions?
#8434
Tech Initiate
diff kit
Ok quick ? which diff kit is best the one for $18.95 or $24.95 I saw on the axiom web site they both have the same parts in the kits. Please help, Need to rebuild my diffs. Thanks for the help.
#8436
Tech Champion
iTrader: (44)
I got my Type R all put together. Tomorrow will be the first race. I am a rookie to electric onroad, but am very experienced in 1/8th buggy. I have a question. I am using a novak gtb with 10.5 motor and foam tires. What throttle profile on the speed control should I use? The track is a tight small course with lots of low speed turns.
hope this helps.
#8437
Tech Champion
iTrader: (73)
I got my Type R all put together. Tomorrow will be the first race. I am a rookie to electric onroad, but am very experienced in 1/8th buggy. I have a question. I am using a novak gtb with 10.5 motor and foam tires. What throttle profile on the speed control should I use? The track is a tight small course with lots of low speed turns.
#8439
LOSI RACER COMING OUT OF RETIREMENT
OK, I've been on "RC Racing Leave" for about a year. Now the baby is a year old and dad wants to start racing again...
As I last called it quits for a while I was running all Ni-MH, not 'cus I like them, but because my 2 JRXS-R (one carpet foam, one carpet rubber) just ran better. They had a little more punch and the setups that we were running were really based on the higher CG of a 6 cell pack. When I'd put in a Li-PO the car didn't have the roll/bite (especially rubber tire on med bite carpet). So, although I was running a steel plate battery tray, I was putting some lead way up high to try to get the same feel..
Anyhow, I've pulled down Mike Haynes recent setups (as well as others), but any comments on running these on LiPO? Change roll center? or just tinker with lead way up high like I used to to get CG in same location as Ni-MH pack??
Cheers,
Mark Taylor
As I last called it quits for a while I was running all Ni-MH, not 'cus I like them, but because my 2 JRXS-R (one carpet foam, one carpet rubber) just ran better. They had a little more punch and the setups that we were running were really based on the higher CG of a 6 cell pack. When I'd put in a Li-PO the car didn't have the roll/bite (especially rubber tire on med bite carpet). So, although I was running a steel plate battery tray, I was putting some lead way up high to try to get the same feel..
Anyhow, I've pulled down Mike Haynes recent setups (as well as others), but any comments on running these on LiPO? Change roll center? or just tinker with lead way up high like I used to to get CG in same location as Ni-MH pack??
Cheers,
Mark Taylor
#8441
Tech Elite
iTrader: (16)
Mark, I'm fortunate enough to see Mike almost every weekend at 360 R/C Speedway In NY and he runs LiPo in his TypeR's, so any recent setups you see from him will already be based on the low CG of a LiPo and I wouldn't worry about putting any weight up high to simulate a NIMH pack...
#8442
most people are just using one screw to hold the fan onto the bulkhead when using the 25mm fan... but i never had a problem with the 20mm novak fans.
#8443
Mark, I'm fortunate enough to see Mike almost every weekend at 360 R/C Speedway In NY and he runs LiPo in his TypeR's, so any recent setups you see from him will already be based on the low CG of a LiPo and I wouldn't worry about putting any weight up high to simulate a NIMH pack...
I've been going back through many, many pages through this thread to find out what LiPO's to buy that have great punch and will fit. What LiPO's is Mike running?? I'm still running Orion 4800 20c, but would like to try some 30 or 35C batteries.
#8444
Tech Elite
iTrader: (16)
Mark,
Mike is running the SMC 5300's, they take some grinding on the pulleys to fit in the car from what I understand, also some grinding on the steel LiPO plate if you[re gonna use that.
I'm running the Orion 5000 Platinum II which fits right in with no need for any extra work. I can't say it's the equal of the SMC, but I can't say it isn't either. I'm not feeling any lack of power in any way. I don't know the C rating of the PlatinumII, but make no mistake, internal resistance and average voltage over the duration of the race would be FAR more important in determining the performance of a pack. That being said, the higher C rated packs should tend to have lower internal resistance, but it's not always a certainty. In any event, the SMC packs are great packs if you don't mind the minor work to get the chassis to accept them. If you'd rather go for a direct fit, I don't think the Platinum II will disappoint you.
Losi have some 4400's that drop right in, I think Larry Fairtrace and Jason Schreffler were running them last time they were at 360 and they were blazing quick, so there's another option to consider.
Mike is running the SMC 5300's, they take some grinding on the pulleys to fit in the car from what I understand, also some grinding on the steel LiPO plate if you[re gonna use that.
I'm running the Orion 5000 Platinum II which fits right in with no need for any extra work. I can't say it's the equal of the SMC, but I can't say it isn't either. I'm not feeling any lack of power in any way. I don't know the C rating of the PlatinumII, but make no mistake, internal resistance and average voltage over the duration of the race would be FAR more important in determining the performance of a pack. That being said, the higher C rated packs should tend to have lower internal resistance, but it's not always a certainty. In any event, the SMC packs are great packs if you don't mind the minor work to get the chassis to accept them. If you'd rather go for a direct fit, I don't think the Platinum II will disappoint you.
Losi have some 4400's that drop right in, I think Larry Fairtrace and Jason Schreffler were running them last time they were at 360 and they were blazing quick, so there's another option to consider.
#8445
Tech Addict
iTrader: (16)
Well I raced my JrxsR today for the first time today. I realized pretty quickly that the throttle profile on GTB was the least of my worries. I managed to rip both front A-arms off the car and chew up 2 spurs while practicing and in my quals. However I did have fun. Sedan racing requires a whole lot more concentration when we are turning 8-9 second lap times (small track). Overall my car felt really good when i got into a brief groove, I just could not keep it off the walls. I need some more practice.