Kyosho Ultima RB6 & RB6.6 Car Thread
|
|||
#2162
Tech Elite
iTrader: (166)
the diff before the wc kit never seemed to last to long for me so i ran the bfast which is a great diff. but to be honest the diff in my 6 is super smooth and seems to be lasting a while. I also like the new x gear grease that comes with the kit on my old diffs i ran ae grease which worked good but the new stuff seems to work great and its not ae which makes it even better
#2163
Tech Elite
iTrader: (166)
So its been a while since I have posted on here, but I figured I would help out my sponsors and show off my RB6 build and what they have helped me with. Just a disclaimer, I built it the way I wanted it to look and hopefully perform to my best abilities. And in no way state that you have to do what I did. We are all adults, well most of us, and you can do whatever you like to your toys.... Period...
So with that said, enjoy, comment, flame and ask questions....
So with that said, enjoy, comment, flame and ask questions....
#2165
Tech Adept
First club race yesterday here in Greece with the RB6 preping for the upcoming National race and my first win since I went with Kyosho two years ago.
This car is so much easier to push than the RB5...I was cruising all day and IF I made any mistakes I could push really hard for a couple of laps and make up for the lost time!
Track was low to medium traction and I made some small changes to my base setup and the car felt just perfect...I had some push on power in the one corner exit but I quess that is down to soft rear spring (used pink to get some traction)
Great car!
This car is so much easier to push than the RB5...I was cruising all day and IF I made any mistakes I could push really hard for a couple of laps and make up for the lost time!
Track was low to medium traction and I made some small changes to my base setup and the car felt just perfect...I had some push on power in the one corner exit but I quess that is down to soft rear spring (used pink to get some traction)
Great car!
#2167
Tech Adept
#2168
Tech Addict
Ran the car for the first time on damp astro in mid config and it's v nice.
Kit used
Savox 1257 servo
Sanwa 451 RX
SP LPF ESC
SP 8.5
My Orion R10 and 8.5 VST is in my DB1.
#2169
My attempt at the T-plate Chassis mod...
Cut down RB5 T-plate
Cut down RB5 T-plate
Installation
Completed
Notice, There is a slight bulge to the chassis after installation. I made sure that the T-plate sit flush on the bottom of the second/lower pocket as well.
This is without shaving anything off the thickness of the T-plate.
Cut down RB5 T-plate
Cut down RB5 T-plate
Installation
Completed
Notice, There is a slight bulge to the chassis after installation. I made sure that the T-plate sit flush on the bottom of the second/lower pocket as well.
This is without shaving anything off the thickness of the T-plate.
#2170
Thanks D....
Practice for sure....
HAHA!!!
I was thinking of doing that, but I need it to appeal to the masses. I didn't want to look to "Pro". But thanks for the idea....
Practice for sure....
HAHA!!!
I was thinking of doing that, but I need it to appeal to the masses. I didn't want to look to "Pro". But thanks for the idea....
#2171
Super Moderator
iTrader: (81)
Slant EyEs (Jason?): if you have any feedback to Diggity or maybe they are reading this perhaps they could put a tongue on the front of the battery strap to help keep that piece of foam in the car during violent crashes. Or is it stuck in there pretty good from the bottom?
#2173
Not sure but if you took a couple of thousands off the tangent of the bottom of the case you could probably get away with it. Tough to tell which part of the case is preventing a flat fit. It bulged just ever so slightly...
#2174
Tech Regular
iTrader: (15)
Saturday went and practiced track had great traction and was clipping off fast ave 15 sec laps with my T plate mod . we raced Sunday traction was down as lap times came with it . managed to Qualify 3rd in A Main pulled off the win . will have video up later . changed my colors to light blue & white with white wing. yes seems to be a very slight bulge under trans did not hurt handling thou
#2175
Tech Master
iTrader: (43)
Caught part of a pipe last night and broke the rear pivot block part: UM508C.
Can I replace this part w/ the ST Racing Aluminum Rear Pivot Block Set that is listed for the RB5?
Part: http://www.teamstrc.com/index.php?ro...product_id=688
The RB5 part is: UM508B, which is the same as the ST Racing block. UM508C is the same as the UM508B, but has been updated for the wing mount - according to the description.
Can I use the ST Alum Rear Pivot Block set on the RB6?
Thanks.
Can I replace this part w/ the ST Racing Aluminum Rear Pivot Block Set that is listed for the RB5?
Part: http://www.teamstrc.com/index.php?ro...product_id=688
The RB5 part is: UM508B, which is the same as the ST Racing block. UM508C is the same as the UM508B, but has been updated for the wing mount - according to the description.
Can I use the ST Alum Rear Pivot Block set on the RB6?
Thanks.