Team Associated TC6 Thread
#1068
Tech Elite
iTrader: (39)
Any ideas?
#1069
Tech Elite
iTrader: (118)
I have the exact same problem. I just finished building the car and through building it i noticed the bottom deck is tweak. Wobble side to side when on a flat surface. Ive over looked everything so I don't know what the issue is. Out of 6 other high end cars Ive built/driven, I've never had one like this out of the box
Any ideas?
Any ideas?
Take the tires off... put the chassis on a flat surface.. loosen ALL the screws on the top deck and shock tower mounts. While holding the chassis down flat on the surface from the top. Start tightening all the screws down.. in an X-pattern from front to back to front, etc... That should get rid of your tweak.
#1072
I have the exact same problem. I just finished building the car and through building it i noticed the bottom deck is tweak. Wobble side to side when on a flat surface. Ive over looked everything so I don't know what the issue is. Out of 6 other high end cars Ive built/driven, I've never had one like this out of the box
Any ideas?
Any ideas?
#1075
Hey guys,
Just unpacked my TC6 and after reading this thread I’m paranoid about missing parts and unthreaded bulkheads…
After inspecting the bulkheads which all had threads, I placed the main chassis on a flat surface and I found the chassis to be twisted and rocking from side to side.
Has anyone else had this and did you contact AE for a replacement??
Just unpacked my TC6 and after reading this thread I’m paranoid about missing parts and unthreaded bulkheads…
After inspecting the bulkheads which all had threads, I placed the main chassis on a flat surface and I found the chassis to be twisted and rocking from side to side.
Has anyone else had this and did you contact AE for a replacement??
I'll be sure to check mine carefully when it arrives...
#1076
hi all, I bought my TC6 on Tower H. and when he came to my home in Spain, the first thing I did was check everything right and get the mount ..... not a single failure in any part ..... in fact already have shot at least 18 batteries ...... a luxury to have this model ......
greetings from Spain to all
Juan Carlos
greetings from Spain to all
Juan Carlos
#1077
Tech Fanatic
iTrader: (1)
New gear chart for tc6
Tested on 48 module, for 64 should be fine it is only mathematics
http://abram.eu.org/gear_tc6.php
29x87 on 48p will not fit it need 0.2mm more
Tested on 48 module, for 64 should be fine it is only mathematics
http://abram.eu.org/gear_tc6.php
29x87 on 48p will not fit it need 0.2mm more
#1078
Tech Apprentice
iTrader: (1)
This is the first time I've built a TC kit and found a tweaked chassis, I'm a bit disappointed.
Can anyone tell me if associated is likely to send me a replacement for this faulty main chassis? I've emailed them with my receipt and still waiting on a reply.
#1079
The first thing I checked was the bulk heads and the chassis on a flat surface with no parts attached.
This is the first time I've built a TC kit and found a tweaked chassis, I'm a bit disappointed.
Can anyone tell me if associated is likely to send me a replacement for this faulty main chassis? I've emailed them with my receipt and still waiting on a reply.
This is the first time I've built a TC kit and found a tweaked chassis, I'm a bit disappointed.
Can anyone tell me if associated is likely to send me a replacement for this faulty main chassis? I've emailed them with my receipt and still waiting on a reply.
If there is a problem with a new kit or part they will take care of you.
#1080
check that the motor mount brace (31313) lines up with the chassis hole, i had to sand about 1mm to get it to line up.
that could be the cause of your tweek.
that could be the cause of your tweek.