NEW HOBBYWING STOCK SUPERCHARGED SOFTWARE
#9751
Is the 504 software for the program box compatible with v2.1 esc?
#9752
Tech Adept
whether antilockbrake feature can cause damage to the esc?
#9755
Moderator
iTrader: (9)
Join Date: Jan 2004
Location: Outside doing things in places... Denver, CO
Posts: 4,609
Trader Rating: 9 (100%+)
I have a Hobbywing 1S 120A that anytime I try flashing the "No_Timing" firmware onto the ESC, it works, there is no timing options, but the LED does not flash?
So I am not getting any blinky action in blinky firmware? This a known issue? I've tried reflashing a few times to no avail. I am using the latest Hobbywing software, the box is up to date (1.08_120504), and the ESC is using the v3 930 No Timing firmware ( I think that's the number, I don't have the ESC in front of me to check). It worked before with the old software, not sure what happened with the new stuff.
I need to get this sorted before IIC for obvious reasons.
So I am not getting any blinky action in blinky firmware? This a known issue? I've tried reflashing a few times to no avail. I am using the latest Hobbywing software, the box is up to date (1.08_120504), and the ESC is using the v3 930 No Timing firmware ( I think that's the number, I don't have the ESC in front of me to check). It worked before with the old software, not sure what happened with the new stuff.
I need to get this sorted before IIC for obvious reasons.
#9757
Moderator
iTrader: (9)
Join Date: Jan 2004
Location: Outside doing things in places... Denver, CO
Posts: 4,609
Trader Rating: 9 (100%+)
Ohh, it wont blinky until its recal'd? Good to know!
#9759
Hi, what's a good starting set up for running in a mid size asphalt track (60' x 40')?
I am using a Xerun 120A v2.1 with a Reedy Sonic 9.5 modified motor. FDR setting at 7 currently.
Thanks.
I am using a Xerun 120A v2.1 with a Reedy Sonic 9.5 modified motor. FDR setting at 7 currently.
Thanks.
#9760
Tech Apprentice
hello guys
I have a very important question for me:
the function of the EPA on gas radio, must be 100% or can I decrease? Change will cause problems to the ESC?
I have a very important question for me:
the function of the EPA on gas radio, must be 100% or can I decrease? Change will cause problems to the ESC?
#9761
#9762
Tech Apprentice
If the Turbo is set to start on Full Throttle (Tx full throttle), you won't get any Turbo starting since you will never reach full throttle.
#9763
The ESC does not know the full range of your Tx, and will act as if the input you will give him during calibration actually is full thottle, and will "think" your for example 50% is 100% on the ESC....
But, why do you want to do that?
#9764
Hi Guys
back on board after 2 weeks in thailand for Femca .
Yes you need to recal your radio and esc once you have loaded blinky zero timing to your 120 amp plus also you will notice that the red blink is two times per second and is very faint .
There is alot of miscommunication on the this page so ill read through it and answer accordingly
back on board after 2 weeks in thailand for Femca .
Yes you need to recal your radio and esc once you have loaded blinky zero timing to your 120 amp plus also you will notice that the red blink is two times per second and is very faint .
There is alot of miscommunication on the this page so ill read through it and answer accordingly
#9765
I have a Hobbywing 1S 120A that anytime I try flashing the "No_Timing" firmware onto the ESC, it works, there is no timing options, but the LED does not flash?
So I am not getting any blinky action in blinky firmware? This a known issue? I've tried reflashing a few times to no avail. I am using the latest Hobbywing software, the box is up to date (1.08_120504), and the ESC is using the v3 930 No Timing firmware ( I think that's the number, I don't have the ESC in front of me to check). It worked before with the old software, not sure what happened with the new stuff.
I need to get this sorted before IIC for obvious reasons.
So I am not getting any blinky action in blinky firmware? This a known issue? I've tried reflashing a few times to no avail. I am using the latest Hobbywing software, the box is up to date (1.08_120504), and the ESC is using the v3 930 No Timing firmware ( I think that's the number, I don't have the ESC in front of me to check). It worked before with the old software, not sure what happened with the new stuff.
I need to get this sorted before IIC for obvious reasons.
please recal the radio and esc and let us know how you go .Im sure it is blinking but it is very faint