300LikesTeam Associated TC4
10-07-2005, 12:37 PM
#6633
Check out the top deck:
Pic from the Nats. No idea who's car it is.
Pic from the Nats. No idea who's car it is.
10-07-2005, 12:46 PM
#6634
Tech Apprentice
My guess is Baker by the looks of the Reedy sticks and motor.
10-07-2005, 05:05 PM
#6635
INPUT BEARING CUP
Need a little help
Has anybody seen an aftermarket aluminum input bearing cap?
The original part # from AE is 31098
I have checked Square,3 racing, & Tobbee Craft with no luck.
I some how miss placed the original plastic piece that came with the FT kit.
I would rather buy an aftermarket part to replace the one I lost.
Thanks for your help........
Has anybody seen an aftermarket aluminum input bearing cap?
The original part # from AE is 31098
I have checked Square,3 racing, & Tobbee Craft with no luck.
I some how miss placed the original plastic piece that came with the FT kit.
I would rather buy an aftermarket part to replace the one I lost.
Thanks for your help........
Last edited by RED-LINE M03; 10-07-2005 at 05:09 PM. Reason: #%^%&
10-07-2005, 05:12 PM
#6636
AE Looking Very Strong in Florida
AE is looking very strong in Florida.
Barry Baker is finding the fastest way around the track in 19 turn.
http://www.rcresults.com/clubs/OnRoad_Nationals/
Later,
E
Barry Baker is finding the fastest way around the track in 19 turn.
http://www.rcresults.com/clubs/OnRoad_Nationals/
Later,
E
10-07-2005, 06:20 PM
#6637
Spool vs: One-way
I've been running a front one-way stock/rubber/carpet.
What difference should I expect from a spool. I'm guessing I could brake into the corners, etc, but does it cause understeer on power, etc?
What difference between a center one-way and my usual front one-way?
Appologies if this has already been discussed, but I read back quite a ways before asking...
Many thanks,
Scottrik
What difference should I expect from a spool. I'm guessing I could brake into the corners, etc, but does it cause understeer on power, etc?
What difference between a center one-way and my usual front one-way?
Appologies if this has already been discussed, but I read back quite a ways before asking...
Many thanks,
Scottrik
10-07-2005, 07:53 PM
#6638
New Body Holes
I just ordered the TC$ conversion. I understand that the body post locations are different. Can you put new holes in old body are the new and old holes too close together?
10-07-2005, 08:23 PM
#6639
Tech Apprentice
Originally Posted by LasagnaCat
For what it's worth, Tower has it listed as "order pending" at just a tick under $200 (currently.)
10-07-2005, 08:49 PM
#6640
TC4 Conversion Link
Here is the link from the AE newsletter:
http://www.rc10.com/shusting/Catalog...versionkit.htm
http://www.rc10.com/shusting/Catalog...versionkit.htm
10-07-2005, 09:38 PM
#6641
Originally Posted by volracer
I just ordered the TC$ conversion. I understand that the body post locations are different. Can you put new holes in old body are the new and old holes too close together?
10-07-2005, 10:57 PM
#6642
Tech Apprentice
Originally Posted by volracer
Here is the link from the AE newsletter:
http://www.rc10.com/shusting/Catalog...versionkit.htm
http://www.rc10.com/shusting/Catalog...versionkit.htm
10-08-2005, 12:57 AM
#6643
Tech Apprentice
Originally Posted by seamus0g
Check out the top deck:
Pic from the Nats. No idea who's car it is.
Pic from the Nats. No idea who's car it is.
