R/C Tech Forums - Search Results
R/C Tech Forums

Go Back  R/C Tech Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Wiki Posts
Calendar
Today's Posts
Search
Vendor Directory
Search: Posts Made By: YoDog
Showing results 1 to 10 of 10
Search took 0.01 seconds.
Forum: Radio and Electronics
02-06-2016, 02:39 PM
Replies: 734
Views: 201,941
Posted By YoDog

Check to make sure your neutral point is stable....

Check to make sure your neutral point is stable. Recalibrate your ESC/transmitter and let the car sit with your radio on and see if the led indicator on the ESC changes color or blink pattern. It may...
Forum: Radio and Electronics
02-06-2016, 02:31 PM
Replies: 734
Views: 201,941
Posted By YoDog

Either borrow a PC with the HW software installed...

Either borrow a PC with the HW software installed and update your box or pick up a cheap laptop and use it for your racing computer. I just got an older Windows 7 laptop for free and dedicated it for...
Forum: Radio and Electronics
01-19-2016, 12:18 PM
Replies: 734
Views: 201,941
Posted By YoDog

Of course you still need the switch. No software...

Of course you still need the switch. No software that I know of can bypass an electro-mechanical function.
Forum: Radio and Electronics
01-19-2016, 12:15 PM
Replies: 734
Views: 201,941
Posted By YoDog

It sounds like you are getting a power supply...

It sounds like you are getting a power supply loop back. Are you running a booster or receiver pack? Is anything plugged into the fan port or programming port? Try disconnecting everything from the...
Forum: Radio and Electronics
06-09-2015, 04:58 PM
Replies: 734
Views: 201,941
Posted By YoDog

Where do you have the end bell timing set? 3.8...

Where do you have the end bell timing set?
3.8 FDR is in the ballpark but you can probably go a little lower depending on your track. Have you had a chance to run the car on the ground yet? I ask...
Forum: Radio and Electronics
06-05-2015, 03:48 PM
Replies: 734
Views: 201,941
Posted By YoDog

Ok, now we are talking about something different....

Ok, now we are talking about something different. At least you can now go through calibration.
Where it says to set your channel reverse to "REV" is for Futaba radio systems, not Sanwa/Airtronics....
Forum: Radio and Electronics
06-02-2015, 10:19 AM
Replies: 734
Views: 201,941
Posted By YoDog

What type of radio system are you using? It's...

What type of radio system are you using?
It's possible that you need to bind your receiver to the transmitter first. With your radio on, you will want to then hold the power button till you hear a...
Forum: Radio and Electronics
06-01-2015, 06:07 PM
Replies: 734
Views: 201,941
Posted By YoDog

For most conditions you should run between 6.8...

For most conditions you should run between 6.8 and 7.5 FDR with a 5.5t motor on boost. Back off the turbo delay to .2sec and dis-engage voltage cutoff. CAUTION!!! Do not run for more than 6 minutes...
Forum: Radio and Electronics
09-23-2014, 10:45 AM
Replies: 734
Views: 201,941
Posted By YoDog

What??? Who would you pay $3.99 to? I would...

What???
Who would you pay $3.99 to?
I would say you have spam issues. The program box can't charge you money. :rolleyes:
Forum: Radio and Electronics
09-12-2014, 09:46 PM
Replies: 734
Views: 201,941
Posted By YoDog

If I remember correctly, the 3.1 ESC may have...

If I remember correctly, the 3.1 ESC may have presets already installed. With the programming box that came with the ESC, only change the mode value. I believe blinky is mode 2. Mode 1 is boosted...
Showing results 1 to 10 of 10


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.