NEW HOBBYWING STOCK SUPERCHARGED SOFTWARE
#1261
Tech Rookie
CobraRacing - The message says it is a database update (1.79) rather than a new version of the software. The start of the message is attached below.
Foodie - I just tried it your way and it worked. Thanks very much for the help.
;*******************************
readme.txt
2010-9-17
CAR_ESC_readme.txt
database version:1.79
The new firmware "100912-2R" of XERUN-80A,XERUN-150A EZRUN-SC10 ,EZRUN-SC8 has the following improvement:
1.Eliminates the bug of ESC shortly been shut off(usually several seconds) caused by mistakenly thermal protection
2.Optimize the switching of forward and backward
Foodie - I just tried it your way and it worked. Thanks very much for the help.
;*******************************
readme.txt
2010-9-17
CAR_ESC_readme.txt
database version:1.79
The new firmware "100912-2R" of XERUN-80A,XERUN-150A EZRUN-SC10 ,EZRUN-SC8 has the following improvement:
1.Eliminates the bug of ESC shortly been shut off(usually several seconds) caused by mistakenly thermal protection
2.Optimize the switching of forward and backward
#1262
HW stock motor
Cobraracing or anybody, whats the spec like for HW 11.5T stock motor? Can't find any info on it. Can the timing endbell be adjusted. Looks cool though. If anybody has experience running them can you pls share as well.
#1263
my speedo as also a updated to 1.79,
also if i click on the device and then the brushless system analyzer it briefly shows a data recorder graph, this then disappears if the program box is connected
if the program box is not connected you can see the data recorder is this a on going up date ?
also if i click on the device and then the brushless system analyzer it briefly shows a data recorder graph, this then disappears if the program box is connected
if the program box is not connected you can see the data recorder is this a on going up date ?
Last edited by njt; 09-20-2010 at 01:12 PM.
#1264
The new Hw motors the light blue and silver can have no mechanical end bell timing adjustment .Mechanical timing causes to much heat build up and pinging.HW use internal electronic digital timing which is 100% acurate compared to the old mechanical timing
Last edited by COBRARACING; 09-22-2010 at 03:30 PM.
#1265
Tech Champion
iTrader: (30)
Just wanted to say a quick hello from the off road world.
I Attended the J Concepts NE Championship race last weekend. Ran my HW 120 in 13.5 and open modified. Never changed motors. Used the same HW 13.5 motor in both class - more than fast enough- too fast actually. In 13.5 class I could easily pull anyone on the straights and over the triple jump. Even against the mod guys running 8.5 or whatever. Motor and speedo never got hot. Should have cranked it up some more!!!
I Attended the J Concepts NE Championship race last weekend. Ran my HW 120 in 13.5 and open modified. Never changed motors. Used the same HW 13.5 motor in both class - more than fast enough- too fast actually. In 13.5 class I could easily pull anyone on the straights and over the triple jump. Even against the mod guys running 8.5 or whatever. Motor and speedo never got hot. Should have cranked it up some more!!!
#1266
Good : Nice design, colour and run cooler
Bad : Less torque but mid and top is acceptable. Holes on the can is too big and myself experiencing motor jam once due to sand going inside through the holes and need to cover some holes.
Overall performance thumb up!!
#1267
#1268
#1270
There is 3 new esc's 120 amp 2.1v ,justock and the 21.v 120 amp 1s
#1271
#1273
#1275
Tech Elite
iTrader: (5)
The more timing a motor may have in another way, will create heat and stop you adding timing via the esc, and really I suspect your best map or timing profile for power 'and' speed will come using esc timing alone.
Of course I have read in a couple of posts where some have said that felt they got a better setup using some endbell timing, but I think it's a nice way to make the setup more complex.
I'd rather let the esc do 'all' the work, then I can also just plug in the box and tweak settings the easy way, when I started using mine I set the timing on my SP10.5 to 0, so far have not felt the need to change it.