NEW HOBBYWING STOCK SUPERCHARGED SOFTWARE
#9241
Tech Master
iTrader: (52)
Ok, time for an update.
Just tried switching pretty much every part around on the motors. Switched out rotors, switched out sensor boards, switched out sensor cables. I've got basically 2x Revtechs and sensor cables and rotors. I've tried every combination of all the parts. Rotor A with Sensor Board A with Sensor Cable A. Rotor B with Sensor Board A with Sensor Cable A, etc etc etc...
Still nothing. It does the same crap as always. Now, I did notice that the first time I fixed it, it had something to do with the sensor cable. Is it possible that I just have absolutely rotten luck and both of the sensor cables I have are faulty? that seems pretty harsh, especially if I just spent the whole night figuring this out...
Just tried switching pretty much every part around on the motors. Switched out rotors, switched out sensor boards, switched out sensor cables. I've got basically 2x Revtechs and sensor cables and rotors. I've tried every combination of all the parts. Rotor A with Sensor Board A with Sensor Cable A. Rotor B with Sensor Board A with Sensor Cable A, etc etc etc...
Still nothing. It does the same crap as always. Now, I did notice that the first time I fixed it, it had something to do with the sensor cable. Is it possible that I just have absolutely rotten luck and both of the sensor cables I have are faulty? that seems pretty harsh, especially if I just spent the whole night figuring this out...
Angelo perhaps send this guy the same software upgrade you sent me.
It sounds very similar to my problem, mine uses to stop start and go slow then kick in.
Best of luck, and rest assured it's nothing to do with the equipment, I went through the annoying task of double checking everything also.
Regards
Nathan
#9242
#9243
Tech Fanatic
iTrader: (27)
Send me an email and ill help you [email protected]
#9244
#9245
Hobbywing Usb link v3.1 download link gives error 404
is there anywhere else to download this ?
V1.64 not works I tried to run it as Admin on Win7 (used to work but not anymore)
Cheers
is there anywhere else to download this ?
V1.64 not works I tried to run it as Admin on Win7 (used to work but not anymore)
Cheers
#9246
Tech Fanatic
iTrader: (10)
#9251
Tech Adept
v3 modified settings
hi guys,
i am running 4.5T thundepower motor in modified. got the new v3. any tips on settings? there seems to be a "default modified" programm set on the speedo? is that safe to use. or do you guys change stuff.
//edit: found it. thx. i will stay with default settings and a 8 FDR for starters.
i am running 4.5T thundepower motor in modified. got the new v3. any tips on settings? there seems to be a "default modified" programm set on the speedo? is that safe to use. or do you guys change stuff.
//edit: found it. thx. i will stay with default settings and a 8 FDR for starters.
Last edited by vitomon; 06-13-2012 at 06:25 AM.
#9252
#9254
hi guys,
i am running 4.5T thundepower motor in modified. got the new v3. any tips on settings? there seems to be a "default modified" programm set on the speedo? is that safe to use. or do you guys change stuff.
//edit: found it. thx. i will stay with default settings and a 8 FDR for starters.
i am running 4.5T thundepower motor in modified. got the new v3. any tips on settings? there seems to be a "default modified" programm set on the speedo? is that safe to use. or do you guys change stuff.
//edit: found it. thx. i will stay with default settings and a 8 FDR for starters.
I have, with help from a mate, changed the Boost settings and added Turbo.
Here is a link to download the PDF setupsheet(the file was to big to upload):
https://dl.dropbox.com/u/31035638/4....-%20Odense.pdf
On the fast flowing track i tested, the temps were actually the same with the added boost and turbo, as with the standard modified program on 7 min runs.
I geared from 8.00-8.30 and the endbell timing from 5-10 deg.
The changes gave more power and topspeed, but still had a smooth linear feel.