Rc10ntc3
#181
Kansasracer- you got rid of the all mighty Mugen? the world is coming to a end... haha I believe this car will make Nitro racing fun.
#183
Kansas racer, how much are you selling the MTX-2 for? Is it eBay bound?
I also contemplated on getting a NTC3 but my MTX-2 is sooo dialed right now i'm afraid to start all over again if I opt for the NTC3. The thing that gets me is when when I see a NTC3 roll all by itself even on a very slight grade. You could probably even move it by just blowing on it.
I also contemplated on getting a NTC3 but my MTX-2 is sooo dialed right now i'm afraid to start all over again if I opt for the NTC3. The thing that gets me is when when I see a NTC3 roll all by itself even on a very slight grade. You could probably even move it by just blowing on it.
#185
Kansasracer- Of course I have one.I think it a cool car that will be easier to setup and drive.I sold my XXXS because I didnt like working on it.The TC3 is faster when I remember how to drive.Let me know what starter box you use.I havent found one that I like.
#186
Regional Moderator
iTrader: (3)
FREAKAH:
Email me @ [email protected] if interested in it. I am not putting it on Ebay. I want it to go to a good home...I'm gonna miss it
Craig: I am going to try and use my Dynamite starter box(I think its just like all the others). THe car is still in the box right now. Won't get a chance to start on it until at least next week...
Email me @ [email protected] if interested in it. I am not putting it on Ebay. I want it to go to a good home...I'm gonna miss it
Craig: I am going to try and use my Dynamite starter box(I think its just like all the others). THe car is still in the box right now. Won't get a chance to start on it until at least next week...
#187
Originally posted by Besercoe
Hey Bk
Have you spoken to guy about lemans, and are you going to racing tonight?
Hey Bk
Have you spoken to guy about lemans, and are you going to racing tonight?
no racing tonight, i will be at HX
#188
Tech Apprentice
Pics of NTC3
Here's my NTC3 Wrapped in WRX skin
#189
Tech Apprentice
Pics of NTC3
Here's the other side
#190
Tech Apprentice
Pics of NTC3
And the front
#191
Regional Moderator
iTrader: (3)
Gonna start assembly probably this weekend. Looking at the manual, I noticed that the steering is not Ball bearing. Does anyone find this a necessary upgrade for this car? (looking for responses from people that actually have RUN the car.
Any other hopups done that I should be doing at the point of assembly?
Thanks
Any other hopups done that I should be doing at the point of assembly?
Thanks
#192
Tech Elite
iTrader: (2)
anyone can post the pic about their starter box ? i find that no matter what i do, ntc3 wont fit perfectly on the standard starter box (i change the orientation of the pully already .....) but u know, the fly wheel of the car is not in the centre, it is offset and near the rear end, not similar to typical shaft-drive car .... any one can give me a hint ?
#193
I haven't run mine yet but I set up my Ofna box to see these starter box issues for myself and it looks like it will be fine. I have the bumper facing away from the handle, motors to the the handle side, using the cut out by the servo for location up front. Come to think of it I haven't checked to see that the wheel will spin the flywheel in the right direction but if it doesn't I'll just swith polarity on the motors.
#194
KansasRacer: All I have done is the turnbuckles.I did get the solid Diff and lightweight clutch housing
#195
Tech Rookie
I've run mine a couple of times. The only upgrade I'd make is to use the GT slipper spring on the servo saver. The stock one is too weak.