orion r10 pro question
#1
orion r10 pro question
ive put this in onroad as its their advice im after regarding brakes
ok guys when i hit the brakes from a high speed the brakes kind of ease in and just before the apex of a corner itll suddenly brake harder,i have it all set to 100% so cant work out why the delay,any help would be very much apreciated,im losing so much time on poor braking performance,id prefer to be able to lock the wheels and the adjust the transmitter,but im maxed on everything
ok guys when i hit the brakes from a high speed the brakes kind of ease in and just before the apex of a corner itll suddenly brake harder,i have it all set to 100% so cant work out why the delay,any help would be very much apreciated,im losing so much time on poor braking performance,id prefer to be able to lock the wheels and the adjust the transmitter,but im maxed on everything
#2
or is there somewhere else on the forum i can ask about the orion product?
#4
#5
ive done all suggested but still have the delay,cmon guys someone must have an answer for me?
#6
Make sure you are fully updated on your ESC....
First re calabrate your throttle neutral/foward/brake... Try neutral range Low 95 and check inital break setting . I run 62.5% brake setting then set your dragbreak to 10% or higher, if low traction 10% is good if higher traction try a higher %... you just dont want the rear end to come around. So if its spinning out use a lower drag break setting. Do you have the program box??
First re calabrate your throttle neutral/foward/brake... Try neutral range Low 95 and check inital break setting . I run 62.5% brake setting then set your dragbreak to 10% or higher, if low traction 10% is good if higher traction try a higher %... you just dont want the rear end to come around. So if its spinning out use a lower drag break setting. Do you have the program box??
yes,i have tried just about everything to lose the delay but its still there,i have taken a vid of whats happening,knowing my luck thats just the way it is,once i have it uploaded ill post it here
#8
i do like it when im going forward its just when i try to stop,im on the brakes 5 mtrs before anyone else and when i got caught by a faster guy he just wasnt expecting me to brake where i had to,to get it slowed down enough for the turn,its like im only getting 40% then at a certain rpm i get the full works,but it always catches me out,the other guys are just having a quick stab at the brakes im on it for 1 1/2 seconds at the same corner
#9
#10
Tech Master
iTrader: (49)
heres the vid
http://youtu.be/ljFsxIaV05Y
http://youtu.be/ljFsxIaV05Y
#11
It's basically the same issue you get with the v2 Hobbywings (Orion is Hobbywing V2 hardware), there is a delay in the brakes when going straight to them which is not present if you pause and then brake.
Hobbywing have (somewhat) addressed this with the newest blinky software but I don't believe that is an option for the Orion speedo.
Hobbywing have (somewhat) addressed this with the newest blinky software but I don't believe that is an option for the Orion speedo.
#12
Tech Lord
iTrader: (52)
Isn't there an "initial brake" setting? like a brake curve?
(edit:Initial BrakeForce
minimum brake. This parameter adjusts the minimum amount of braking power when the brakes engage. The default value is qual to the drag brake value. A high value can cause the wheels to lock immediately when the brake is used.)
Maybe set your initial brake force higher? That issue would drive me bananas... i would consider that almost unusable. I need my brakes to be consistent and predictable to make the best out of my apexes.
(edit:Initial BrakeForce
minimum brake. This parameter adjusts the minimum amount of braking power when the brakes engage. The default value is qual to the drag brake value. A high value can cause the wheels to lock immediately when the brake is used.)
Maybe set your initial brake force higher? That issue would drive me bananas... i would consider that almost unusable. I need my brakes to be consistent and predictable to make the best out of my apexes.
#13
Isn't there an "initial brake" setting? like a brake curve?
(edit:Initial BrakeForce
minimum brake. This parameter adjusts the minimum amount of braking power when the brakes engage. The default value is qual to the drag brake value. A high value can cause the wheels to lock immediately when the brake is used.)
Maybe set your initial brake force higher? That issue would drive me bananas... i would consider that almost unusable. I need my brakes to be consistent and predictable to make the best out of my apexes.
(edit:Initial BrakeForce
minimum brake. This parameter adjusts the minimum amount of braking power when the brakes engage. The default value is qual to the drag brake value. A high value can cause the wheels to lock immediately when the brake is used.)
Maybe set your initial brake force higher? That issue would drive me bananas... i would consider that almost unusable. I need my brakes to be consistent and predictable to make the best out of my apexes.
#15