OFNA GT-V2e 1/8 GT
#721
OK guys this thread can now get back on topic and i will now be more involved with it especially since this chassis is about to be come REALLY popular, and a suspension has been hammered down by the powers that be!!
#723
Tech Elite
iTrader: (2)
I did and I'm sure they will take care of it.
The RCB fronts mount up and would look right at home if they didn't have so much "patina" on them. Will take some tuning to get the balance right but shiz happens.
I had a couple of deals fall through so its karma for this one to stay. With the development work/upgrades going on there should be plenty to keep me interested.
Need to get a GT8 scene going in Tampa. We have outdoor clay and indoor carpet but not much in the way of on-road.
The RCB fronts mount up and would look right at home if they didn't have so much "patina" on them. Will take some tuning to get the balance right but shiz happens.
I had a couple of deals fall through so its karma for this one to stay. With the development work/upgrades going on there should be plenty to keep me interested.
Need to get a GT8 scene going in Tampa. We have outdoor clay and indoor carpet but not much in the way of on-road.
#724
The guys in brownsville parking lot race every other sunday and probably have the biggest group around! the convinced and old TARGET to allow them to use their parking lot. one of the locals built a moveable track system out of wood and the have a blast! You will probably have to grassroots it to get it going!! You do not need much to start and yo ucan get a robotronic counting sytem for around 400.00 with a few transponders and they only cost 40.000 retail! post up on the GT thread and ask and keep an eye out for IGT8F.com lots of new developments coming in a week or so, its going to be exciting!
#725
Tech Initiate
Ya, I've been tweaking my car for months now but I bought the RTR, my car is almost full pro now. All I need is towers at this point. Ill probably go SNR Graphite on those instead of aluminum. I'm going to pick up the material for my custom top plate in a few. So tired today Might not work on it...
#726
Tech Master
iTrader: (45)
Working on the build. Next shopping trip will be for larger pinions. 18t is the largest I have on hand and it barely reaches the spur.
The stock front springs seem really short. The collars are screwed all the way down just to make contact. Can anyone confirm this is correct?
#732
Tech Initiate
Pro chassis comes with a 16/42 gearing as well. I busted my 42 spur and put on a backup 46 spur with 18 pinion and I ran out of space on mount slider. Had to mill out a few mm to squeeze on the 18. I'm planning to run 41 or 42 spur with 18 pinion, which should work.
With stock 42 spur, I could not install a 14 pinion. So theoretically you should be able to use 16+ pinions. The RTR motor mount is different than the Pro but should fit same gearing.
With stock 42 spur, I could not install a 14 pinion. So theoretically you should be able to use 16+ pinions. The RTR motor mount is different than the Pro but should fit same gearing.
#733
Tech Elite
iTrader: (2)
Pro chassis comes with a 16/42 gearing as well. I busted my 42 spur and put on a backup 46 spur with 18 pinion and I ran out of space on mount slider. Had to mill out a few mm to squeeze on the 18. I'm planning to run 41 or 42 spur with 18 pinion, which should work.
With stock 42 spur, I could not install a 14 pinion. So theoretically you should be able to use 16+ pinions. The RTR motor mount is different than the Pro but should fit same gearing.
With stock 42 spur, I could not install a 14 pinion. So theoretically you should be able to use 16+ pinions. The RTR motor mount is different than the Pro but should fit same gearing.
#734
Tech Elite
iTrader: (2)
Pro chassis comes with a 16/42 gearing as well. I busted my 42 spur and put on a backup 46 spur with 18 pinion and I ran out of space on mount slider. Had to mill out a few mm to squeeze on the 18. I'm planning to run 41 or 42 spur with 18 pinion, which should work.
With stock 42 spur, I could not install a 14 pinion. So theoretically you should be able to use 16+ pinions. The RTR motor mount is different than the Pro but should fit same gearing.
With stock 42 spur, I could not install a 14 pinion. So theoretically you should be able to use 16+ pinions. The RTR motor mount is different than the Pro but should fit same gearing.
#735
Tech Initiate
I think a mix of drag racing my friends on 6s and poor meshing. Do NOT launch the car haha. It was for fun but its a track car now so it wont happen again, hopefully.