Awesomatix EP Touring Car (A700 Shaft Drive)
#3676
Tech Adept
Ok
Sorry for my poor english
Sorry for my poor english
#3677
Tech Fanatic
#3678
Tech Rookie
hi, can we have setup from last ets?
#3679
Tech Fanatic
#3680
Tech Rookie
#3681
Tech Adept
Well,
I didn't want to go to the track before being sure everything is ok.
So i checked everything.
Result: 2 springs bent
So i changed all the four to hard ones.
But now, i still have a problem.
At the rear left side, there is almost 2mm play before the suspension begins to work.
It's like there is not enough downstop (5mm), but on the right side, there is no problem...
Does anybody know?
Hope you understand what i mean.
Cheers
I didn't want to go to the track before being sure everything is ok.
So i checked everything.
Result: 2 springs bent
So i changed all the four to hard ones.
But now, i still have a problem.
At the rear left side, there is almost 2mm play before the suspension begins to work.
It's like there is not enough downstop (5mm), but on the right side, there is no problem...
Does anybody know?
Hope you understand what i mean.
Cheers
#3682
Tech Master
iTrader: (44)
Well,
I didn't want to go to the track before being sure everything is ok.
So i checked everything.
Result: 2 springs bent
So i changed all the four to hard ones.
But now, i still have a problem.
At the rear left side, there is almost 2mm play before the suspension begins to work.
It's like there is not enough downstop (5mm), but on the right side, there is no problem...
Does anybody know?
Hope you understand what i mean.
Cheers
I didn't want to go to the track before being sure everything is ok.
So i checked everything.
Result: 2 springs bent
So i changed all the four to hard ones.
But now, i still have a problem.
At the rear left side, there is almost 2mm play before the suspension begins to work.
It's like there is not enough downstop (5mm), but on the right side, there is no problem...
Does anybody know?
Hope you understand what i mean.
Cheers
Monti
#3683
R/C Tech Elite Member
iTrader: (28)
Since there where two bent spr01s --- What else is bent. Please check to see if these are bent--
Spr02
C04
Disconnect the am06/p04 from the c04. Does the arm move freely??
Does the p01/p02 move freely only the on the st14?
Does the p13 move freely on the st14 when the p01/p02 is disconnected from the am06?
Spr02
C04
Disconnect the am06/p04 from the c04. Does the arm move freely??
Does the p01/p02 move freely only the on the st14?
Does the p13 move freely on the st14 when the p01/p02 is disconnected from the am06?
#3685
Tech Adept
Everything moves freely, C04 isn't bent.
I'm not sure if spr02 is bent but i think not.
When i put the car with wheels on it it works normally.
Cheers
I'm not sure if spr02 is bent but i think not.
When i put the car with wheels on it it works normally.
Cheers
#3686
R/C Tech Elite Member
iTrader: (28)
i was building a car for a friend tonight -- and while applying the final setup i noticed the rear end was overly stiff, and had a different feel from left to right. the problem ended up being a binding of the rear toe links and the above set screws holding the upper links. the simple solution was using shorter set screws in my upper links. the car features am19 camber plates.
#3687
Wanted to buy
Hi there, I am looking to buy 1x used A700l or ex. Please send me a PM. Thanks.
#3688
Awesomatix USA's new factory driver
#3689
#3690
Is that Larry fairtrace wow he aged