Randy_Pike

iTrader: (6)

Orbital, great idea. I'll work on that.


194 has a lot of low voltage improvements. We're working on the 1s profile stuff right now.

Boost is stronger on the lower portion of the scale say between 1-10. We're working on something else to get more top end, it's coming.

Randy_Pike

iTrader: (6)

Quick how to video for Vista Users!:

http://www.youtube.com/watch?v=tTp3tUL9u8Y

or8ital

iTrader: (38)

Ran v194 tonight on carpet. Couldnt find the right gearing. The car was very slugish. Ran the 17.5 Redline for a couple minutes at 4.2 FDR and max boost and got to 115. Dropped it down to 4.6 FDR and ran it a couple more minutes. Car was no faster and got to 145. Must have still been overgeared??

I then ran a 21.5 Redline at 4.7 FDR and it felt slow as well but only got up to 110 after 5 min. Dropped it down to 4.8 FDR and got a tad faster.

Guess I just need to play with it some more. Not sure why the 17.5 was getting so hot so quickly. 4.6 seems pretty conservative but this is my first time playing with the max boost.

Randy_Pike

iTrader: (6)

Try running 10 on the motor and 20 on the boost with 194. I bet you'll like it.

tc4wally

iTrader: (1)

nah mate

running lipo, even tried it with the cut out switch turned off. we run 6 min 17.5 and i use 3800mah so i don't get anywhere near flat in these packs.

have ordered the spektrum cap so will just have to try that.

Randy_Pike

iTrader: (6)

Wally, your issue really sounds like a spektrum dumping out.

The cap should fix your issue.

SRW141

iTrader: (4)

Thanks for the info Randy.

pakk

iTrader: (80)

Correct, 0 timing on the motor because it is not adjustable AFAIK, its set to 0. I am currently @ 3.75 FDR because the motor recommends 3.8 and that is the closest I got. I do have a 5t smaller pinion. You are suggestion I be up around 4.1?


You're saying boost is stronger between 1-10 than 11-100? I'll go try.

--pakk

SRW141

iTrader: (4)

[QUOTE=pakk;5660601]Correct, 0 timing on the motor because it is not adjustable AFAIK, its set to 0. I am currently @ 3.75 FDR because the motor recommends 3.8 and that is the closest I got. I do have a 5t smaller pinion. You are suggestion I be up around 4.1?

If 3.75 FDR was what you where running in 180 and now you are using 194 and setting max boost you will want to go to around 4.1 or maybe lower. Check temps and speed your looking for.

pakk

iTrader: (80)

Well it is not so much that I am trying to match what I was previously running, I have only had this esc about a week.

What I am saying is setting the boost to anything does not seem to do anything.

When timing changes, is it very noticeable?

--pakk

Canuck

iTrader: (25)

I run 8 minutes on 1S with 13.5 and I use only 3000 mah on the pack. I use a booster.

miller tyme

iTrader: (5)

There is no boost 11-100, that would be timing when running in Dual mode. I have found dual mode to have less top end in any wind 10.5 and slower. If you have one of the more current versions software 189 or 194, check the box marked Sensored, the timing slider will change to Boost (0-30), if the motor is at 0, set boost to max, you should be a rocket then. Only run for a minute or so to start so to check motor temp.

haltol

Frend's please send my new software 1.89 & 1.94.
And please my recomend setup ESC for 1/10 xray t'09 for new software for motor 10.5 Fantom sensored (Feigao)

miller tyme

iTrader: (5)

If your slow at 4.2 and cool then went to a 4.6 FDR , that's the wrong way, FDR works opposite roll-out, the farther from 0 you go the slower geared it is. For reference I run my VTA 21.5 at 4.55 FDR and the 17.5 Duo at around 3.4 FDR with 2.20 tires

mikky32

Good news.

Thanks. this helps a lot of people.
Thank you Randy